HERKULES RP1200 Originalbetriebsanleitung Seite 28

8. Unpacking
Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be rec-
ognised.
If possible, store the packaging until the warranty pe-
riod has expired.
Familiarise yourself with the product by means of the
operating instructions before using for the first time.
With accessories as well as wearing parts and re-
placement parts use only original parts. Replacement
parts can be obtained from your dealer.
When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
9. Construction
Fitting the handle (fig. A - F)
• Fasten the handle (2) to the plate compactor (a)
with the help of the screw and the star-grip nut (b).
Screw is pushed through from the outside and fas-
tened with the screw and star-grip nut.
• Now fasten the throttle (1) to the handle (2) (size
8/10). The Bowden cable is fastened to the handle
(2) by mean of cable ties.
Fitting the rubber pad (fig. G + H)
• Rubber pad (c): Place or pull the plate compactor
onto the rubber pad (c) and align the holes. Then
fasten in place from below with the three fastening
screws (e).
Fitting the transport fixture (fig. X + Y)
• Transport fixture (f): Tip the plate compactor for-
wards with the handle (2) and align the transport
fixture (f) in the hole provided for it. The plate com-
pactor can now be set back down again and trans-
ported.
28 | GB
10. Installation
m ATTENTION!
Always make sure the device is fully assembled
before start-up!
Hand Grip (2), (fig. A)
When operating the compactor, use this hand grip (2)
to maneuver the compactor.
Throttle Control (1), (fig. A + C)
The throttle lever (1) controls engine speed. Moving
the throttle lever (1) in the directions shown makes
the engine run faster or slower.
langsam
fast =
slow =
vitesse lente
Lift Point (3) (fig. A)
slow
Used to lift the machine with crane or other lifting de-
vice.
Pomalu
Belt Guard (19) (fig. A)
Remove this guard (19) to gain access to the V-belt.
Pomalý
Never run the compactor without the V-belt guard
(19).
Počasnega
If the V-belt guard (19) is not installed, the possibili-
ty exists that your hand may get caught between the
lassú
V-belt and clutch, thus causing serious injury and
bodily harm.
бавно
Exciter (5) (fig. A)
An eccentric weight mounted on the exciter shaft con-
Nopea
tained within exciter housing is driven at high speed
by a clutch and belt drive system. This high speed
shaft revolution causes the rapid lifting and down-
ward ramming motion of the machine as well as im-
parting a forward motion.
Engine switch (On-Off) (17) (fig. A + I)
The engine switch (17) enables and disables the igni-
tion system. The engine switch (17) must be in the ON
position for the engine to run.
Turning the engine switch (17) to the OFF position
stops the engine.
Check before operation
Check
• Look around and underneath the engine for signs
of oil or gasoline leaks.
• Look for signs of damage.
• Check that all shields and covers are in place, and
all nuts, bolts, and screws are tightened.
www.scheppach.com
schnell
vitesse rapide
langsam schnell
fast
vitesse lente vitesse rapide
rychle slow fast
rýchly Pomalu rychle
hitrega
Pomalý rýchly
gyors
hitrega
Počasnega
бързо lassú gyors
бавно бързо
hidas
Nopea hidas