Technical Data; Before Starting The Equipment - Einhell Rt-Sm 330 U Bedienungsanleitung

Anleitung_RT_SM_330_U_SPK1:_
All persons who use and service the machine have
to be acquainted with this manual and must be
informed about its potential hazards.
It is also imperative to observe the accident
prevention regulations in force in your area.
The same applies for the general rules of
occupational health and safety.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting
from such changes.
Even when the machine is used as prescribed it is
still impossible to eliminate certain residual risk
factors. The following hazards may arise in
connection with the machineʼs construction and
design:
Contact with the saw blade in the uncovered saw
zone.
Reaching into the running saw blade (cut
injuries).
Kick-back of workpieces and parts of workpieces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the saw
blade.
Damage to hearing if essential ear-muffs are not
worn.
Harmful emissions of wood dust when the
machine is used in closed rooms.

5. Technical data

Asynchronous motor
Output
Operating mode
Idle speed n
0
Carbide-tipped saw blade
Number of teeth
Tilting range
Mitre cuts
Sawing width at 90°
Sawing width at 45°
Sawing width at 2 x 45°
(double mitre cuts)
Weight
Noise emission values
The sawʼs noise is measured in accordance with
DIN EN ISO 3744; 11/95, E DIN EN 31201; 6/93,
ISO 7960 Annex A; 2/95. The machine may
exceed 85 dB(A) at the workplace. In this case,
noise protection measures need to be introduced
for the user (ear-muffs).
12.01.2009 17:11 Uhr
Sound pressure level L
Sound power level L
„The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immision level
at the workplace include the duration of impact, the
type of room, and other sources of noise etc., e.g.
the number of machines and other neighbouring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved."
Total vibration values (vector sum of three directions)
determined in accordance with EN 61029.
Vibration emission value a

6. Before starting the equipment

6.1 General
The machine must be firmly mounted in working
position, e.g. on a workbench, the base frame
supplied with the machine, or similar.
All the covers and safety devices have to be
230 V~ 50 Hz
properly fitted before the machine is switched on.
1600 W
It must be possible for the saw blade to run
freely.
S1
When working with wood that has been
4200 min -1
processed before, watch out for foreign bodies
ø 305 x ø 30 x 3,2 mm
such as nails or screws etc.
60
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
-45° / 0°/ +45°
machineʼs moving parts run smoothly.
0° to 45° to the left
Before you connect the machine to the power
330 x 102 mm
supply, make sure the data on the rating plate is
230 x 102 mm
the same as that for your mains.
6.2 Assemble the saw (Fig. 1-3; 11; 12)
230 x 65 mm
To adjust the turntable (17), loosen the locking
36,2 kg
grip (14) by approx. 2 turns, which frees the
turntable (17).
Turn the turntable (17) and scale pointer (15) to
the desired angular setting on the dial (16) and
lock into place with the locking grip (14).
To release the saw from its position at the bottom,
pull the retaining pin (27) out of the motor
mounting while pressing down lightly on the
machine head (4).
Swing the machine head (4) up until the release
Seite 19
Idle speed
95,9 dB(A)
pA
108,9 dB(A)
WA
= 2,630 m/s 2
h
GB
19