Herunterladen Diese Seite drucken

DeLonghi AQVA Bedienungsanleitung Seite 27

Elektrischer handtuchwärmer

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 45
4.5.6 BEHAVIOURAL INDICATOR
The behavioural indicator allows you to check if the chosen
temperature set point is aligned with the recommended guide-
lines, in order to avoid the waste of energy and reduce the en-
ergy consumption.
An arrow will appear by one of the three colored bars that
represent the energy consumption in a qualitative way,
according to the following scheme:
(a) Green: The chosen temperature set point
is already lower than the recommended.
(b) Yellow: The chosen temperature set
a
b
c
point is adequate, but it would be better to
further decrease it.
(c) Red: The chosen temperature set point is
high, it would be better to decrease it.
IMPORTANT! The behavioural indicator gives an exclusively
qualitative indication of the energy consumption. It is NOT
an absolute measure.
IMPORTANT!
IMPORTANT! low battery indication is reset by pressing the
mand sent from the Control Panel after replacing the bat-
teries.
4.6 OPERATION WITH COMMAND STAND-
BY BUTTON
The "Standby" button located on the Command (see Fig. 9)
allows you to turn the towel warmer on and off even without
the Control Panel.
To turn the appliance on and off, press the "Standby" button.
The towel warmer comes on in "Pilot Wire" mode and emits
a beep. On the appliance the upper LED turns red. If the Pilot
Wire is connected and the programming unit is active, the ap-
pliance performs the "Pilot Wire" order set on the program-
ming unit. Otherwise it performs the "Comfort" order.
The appliance emits a double beep when it enters the
"Standby" mode and a single long beep when it exits the
"Standby" mode.
When the towel warmer is turned on using the "Standby"
button on the Command, the "Comfort" temperature is set
at 19°C and all functions are reset to the default values.
To go back to controlling the appliance using the Control
Panel, turn the towel warmer on using the "Standby" button
on the Control Panel. The appliance starts operating with the
modes, temperatures and functions set on the Control Panel.
IMPORTANT: After using the "Standby" button on the Com-
mand, the appliance ignores all orders transmitted by the
Control Panel other than "Standby".
IMPORTANT!
mands to the Control Panel, it can only receive.
IMPORTANT: In case of power down due to a black-out, all
current settings are kept in memory with the exception of
date and time.
If a power failure occurs when the radiator is in "Chrono"
mode, and the set date and time are lost, on recovery the
appliance goes to "Comfort" mode with temperature set at
17 °C.
mand sent from the Control Panel is received.
IMPORTANT: If the appliance remains without power while
the "Overdrive (2h)" function is enabled, the date and time
settings are lost. When power is restored, the appliance exits
the function and resumes functioning in the mode selected
previously.
-
IMPORTANT: In case of power down while the "ASC" func-
tion is enabled, when restored, the function remains active
but a few days will be required for it to become fully opera-
-
tional.
5. CLEANING
Before cleaning, make sure the appliance is turned
off, cold and disconnected from the household mains.
To clean, just wipe with a soft damp cloth and
neutral detergent. Never use abrasive or corrosive
cleaning products or solvents.
surface and inside of the appliance at least twice a
year using a vacuum cleaner.
6. MAINTENANCE
Should any technical problems arise, contact a
the dealer or manufacturer) or your local dealer.
All operations on the appliance must be carried out
ing maintenance must make sure the appliance is
turned off, cold and disconnected from the house-
hold mains.
25
GB
-
-
-

Werbung

loading

Diese Anleitung auch für:

AmelieKarmaAlicante