WOLFF BS 125 Originalbetriebsanleitung Seite 15

Reduce dust exposure:
Particles generated when working with this
machine may contain substances that can
cause cancer, allergic reactions, respiratory
diseases, birth defects or other propagation defects.
Some of these substances include: Lead (in paint
containing lead),mineral dust (from bricks, concrete
etc.), additives used for wood treatment (chromate,
wood preservatives), some wood types (such as
oak or beech dust), metals, asbestos.
The risk depends on for how long the user or
nearby persons are exposed to the substance.
This dust must not be allowed to enter your body.
Do the following to reduce exposure to these
substances: Ensure good ventilation of the
workplace and wear appropriate protective
equipment, such as respirators able to fi lter
microscopically small particles.
Observe the relevant guidelines for your material,
staff , application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work (see
chapter 11.), thus less particles enter the
environment in an uncontrolled manner.
Use a suitable extraction unit. Reduce dust
exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifi ers
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping or
blowing stirs up dust
- Vacuum or wash the protective clothing Do not
blow, beat or brush.
5. Important components See page 2.
1 Spindle locking button
2 Spindle
3 Supporftlange
4 Diamond disc
5 2-hole Adjusting nut *
6 2-hole spanner *
7 Electronic signal display
8 Distance ring
9 Anti vibration grip
11 Sliding on/off switch
12 Lever
13 Safety cover
14 Extractor connection piece
15 Segment for working near walls (open by twisting)
16 Brush rim
6 Commissioning
6.1 Attachguard at the angle grinder
See illustration B on page 2.
- Push and hold the lever (12). Place the safety
guard (13) in the position indicated.
- Release the lever and turn the safety guard
until the lever engages.
- Make sure that the guard is placed securely:
The lever must engage and you should not be
able to turn the safety guard.
(Disassemble in reverse order.)
6.2 Dust extraction
Always use a suitable dust extraction system:
Connect an M-class vacuum cleaner to the
extractor connection piece (14).
For optimal dust extraction, use the connecting
sleeve #66218.
WOLFF recommend:
Wet-dry vacuum cleaner M30 #162780
We recommend using an antistatic suction
hose Ø 35 mm.
Before plugging in, check to see that the
rated mains voltage and mains frequency, as
stated on the rating label, match with your
power supply.
Always install an RCD with a max. trip
current of 30 mA upstream.
7. Attaching the accessory
Prior to any conversion work: Pull the mains
plug from the socket. The machine must be
switched off and the spindle at a standstill.
7.1 Locking the spindle
- Press in the spindle locking knob (1) only
when the spindle is stationary!
- Press in the spindle locking button (1) and
turn the spindle (2) by hand until the spindle
locking button engages.
7.2 Fitting/removing the diamond cup wheel
See illustration A on page 2.
To fi t:
- Fit the support fl ange (3) on the spindle (2).
The fl ange should not turn on the locked
spindle when properly attached.
- Lay 1 or 2 washers on the support fl ange,
depending on how much the diamond cup is worn.
- Lay the diamond disc (4) on the washers
so (3) that it lies fl at along the washers.
- The 2 sides of the clamping nut (5) are diff erent.
Screw the clamping nut onto the spindle so that
the band of the clamping nut (5) is centering the diamond
disc. (Picture F)
15