WOLFF BS 125 Originalbetriebsanleitung Seite 12

EN
Translation of the original instruction manual
1. Declaration of Conformity
We declare under our sole responsibility that this
product is in conformity with the following
standards of standardization documents:
DIN EN 60745-1, DIN EN 60745-2-3,
according to the provisions of the:
2006/42/EC, 2004/108/EC, 2011/65/EU.
Authorised to issue this declaration and for
the gathering of the technical documentation:
UZIN UTZ TOOLS GmbH & Co. KG | D-74360 Ilsfeld | Ungerhalde 1
2. Specifi ed Use
The angle grinders, when fi tted with original
WOLFF accessories, are suitable for grinding, of
concrete, stone and similar materials without
the use of water. The extraction hood is designed to
be attached to the original safety guard for WOLFF
angle grinders as of the year of manu-facture 2008.
The year of manufacture (Y) is specifi ed on the
machine rating plate.
For example:
Uzin Utz Tools GmbH & Co.KG
D-74360 Ilsfeld | Germany
The extraction hood is designed for surface
grinding with diamond cups, fi bre grinding plates
and cling-fi t backing plads. (Attach cling-fi t backing
pads only to angle grinders without Autobalancer).
The maximum permitted diameter of the
accessories is 125 mm (5").
When working with diamond cups, use an angle
grinder with a rated input power of at least 1400W.
Do not use for abrasive cutting-off operations,
roughing work, sanding, polishing or fl ap disc work.
Do not machine anymetallic materials. Suitable for
the extraction of dusts generated during surface
grinding of mineral materials, wood, plastics,
glassfi bre-reinforced plastics, paints and
residue of adhesives.
Always use a suitable dust extraction system:
Connect an M-class vacuum cleaner to the
extractor connection piece (14). We recommend
using an antistatic suction hose Ø 35 mm.
Note: The ring brush maystick when thermoelastic
materials are processed.
The machine must not be used with water.
It is suitable for commercial use in trade and
industry.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
12
Dipl.-Ing. (FH) Dieter Hammel
01.03.2016, i.V
99999999 9994411235
Type
3. General Safety Instructions
For your own protection and for the
protection of your power tool, pay attention
to all parts of the text that are marked with
this symbol!
WARNING – Reading the operating
instructions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in
electric shock, fi re and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your power tool only together with
these documents.
4. Special Safety Instructions
4.1 Safety warnings common for grinding,sanding:
Use
a) This guard is designed for surface grinding.
Read all safety warnings, instructions, illustrations
and specifi cations provided with this guard.
Failure to follow all instructions listed below may
result in electric shock, fi re and/or serious injury.
b) This guard is not suitable for routing, polishing,
sanding, working with roughing discs, wire brushes,
parting grinder discs or fl ap discs.
Operations for which the guard was not designed
may create a hazard and cause personal injury.
c) Do not use accessories which are not specifi cally
designed and recommended for this guard and the
power tool by the manufacturer.
Just because the accessory can be attached to
your power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool.
Accessories running faster than their rated speed
can break and fl y apart.
e) The outside diameter and the thickness of
your accessory must correspond to the dimensions
of your guard and your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) Prior to each use check if parts are missing,
worn, broken, torn or damaged.
Do not use defective or incomplete guard.
g) Use only grinding media approved for your
guard. Grinding media for which the guard was not
designed cannot be adequately guarded and are
unsafe.