Installation - Renkforce T-701B Bedienungsanleitung

G Operating Instructions
T-701B 17,8 cm (7") Monitor
Item no. 373965
Intended use
The monitor is used to play back audio and video signals of externally connected devices in ve-
hicles.
This product is only approved for the connection to 12 V direct current on-board networks with
the negative pole of the battery to the car body. The product may only be installed and operated in
vehicles with this kind of on-board voltage.
The user must make sure that the way the product is installed protects the product from humidity
and wetness.
Any use other than the one described above damages the product. Moreover, this involves dan-
gers such as short-circuit, fire, electric shock, etc..
No part of the product should be modified or reassembled.
This product complies with the applicable national and European requirements. All names of com-
panies and products are the trademarks of the respective owners. All rights reserved.
Always follow the safety instructions.
Safety Instructions
T he warranty will be void in the event of damage caused by failure to observe these
safety instructions! We do not assume liability for any resulting damage.
W e do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions. In such cases, the warranty will
be null and void.
A n exclamation mark inside a triangle points out important instructions in the opera-
ting manual.
T he "arrow" symbol indicates special tips and operating information.
• Extra care should be taken when using the device for the first time. Therefore, please follow the
operating instructions carefully.
• In many countries, the use as a monitor to play back movies etc. while driving is only allowed
for car passengers. The driver must not be distracted by this. Prior to the installation, ask for
information about the statutory regulations in your country.
• For safety reasons, any unauthorised conversion and/or modification to the product is not per-
mitted.
• The device may only be used with the 12 V DC vehicle power supply (with the negative terminal
of the battery connected to the body of the vehicle). Never connect the device to a different
power supply.
• This product is not a toy, it is not suitable for children. Children are not aware of the potential
dangers involved when using electrical devices.
• Do not expose the device to high temperatures, dripping or splashing water, strong vibrations or
heavy mechanical stress.
• Check the device occasionally for damage. Should the device show any sign of damage, do not
use it anymore. Disconnect the device from the power supply (remove the batteries) and take it
to a specialist service centre.
• Only use the device in a temperate climate, never in a tropical climate.
• Do not leave packaging materials unattended. They may become dangerous playthings for
children.
• Also observe the safety and operating instructions of any other devices that are connected to
this device.
• Please observe the additional safety instructions in the individual chapters of this manual.
• If in doubt about how to connect the device correctly, or should any questions arise that are
not answered in these operating instructions, please contact our technical advisory service or
another specialist.
Inserting/changing the batteries of the remote control
Keep batteries out of the reach of children.
Make sure that the polarity is correct when inserting the battery.
Remove the battery when the device will not be used for a while.
L eaking or damaged batteries can lead to caustic burning of the skin. Therefore, use
suitable protective gloves.
M ake sure that the battery is neither short-circuited nor thrown into a fire. Do not
recharge batteries. There is danger of an explosion.
• Pull out the battery holder on the backside of the remote control.
• Remove the discharged battery and insert a new 3 V lithium CR2025 coin cell. The correct pola-
rity is indicated on the battery holder.
• Slide the battery compartment cover on to the remote control again. It must snap in place.
• If the remote control no longer functions properly, the battery is discharged and must be repla-
ced by a new one of the same type.

Installation

The monitor can be set up using the foot enclosed or installed in a headrest or installation opening,
e.g. in a caravan, using the mounting frame.
P lease select the place of installation carefully so that the device neither influences
the driver's activity nor distracts him from the traffic.
D o not install any components within the range of the fully-expanded airbag, as this
could lead to injury to the vehicle's occupants in the event of an accident.
M odifications to the vehicle which are made necessary through the installation of the
monitor or other components must always be carried out in such a manner that neither
the traffic safety nor the designed stability of the car is impaired. With many vehicles,
the MOT will be void, if you cut out a section of the sheet metal.
B efore drilling the attachment holes, make sure that the electric cables, brake lines,
the fuel tank or similar systems will not be damaged.
W hen installing the monitor, take into consideration the risks that can arise from de-
vices being dismounted in the event of an accident. Therefore mount it safely and in a
place where it cannot become a danger for the passengers.
• Push the two enclosed plastic wedges between monitor and mounting frame in the area of the
retaining brackets.
• Pull the monitor out of the mounting frame.
Installing the foot
• Attach the foot to the installation surface with the adhesive pad included in the delivery or use
suitable screws.
• If you decide to use the adhesive pad for mounting the foot, clean the mounting surface with
a suitable cleaning agent before you start. Please note that the temperature must be at least
15 °C when using the adhesive pad.
• The mounting surface on the foot can be bent and thus, adjusted to possible curves in the set up
area.
• Push the monitor with the fastening rail on the back of the housing onto the foot and carefully
tighten the clamping screw.
• The angle of the monitor can be adjusted with the second screw on the foot.
Installation
• Cut out a mounting opening of 177 x 120 mm. The required mounting depth is 18 mm.
• Glue the mounting frame onto the mounting surface or bolt it down. For this purpose, the moun-
ting frame provides corresponding holes.
Turn the mounting frame so that the opening for the connection cable is on the bottom
right.
• After completion of the connection work (see next chapter), insert the monitor into the mounting
frame and snap it into place.
Connection
The electric connection should always be carried out by a specialist.
T o avoid short-circuits and resulting damages of the device, the negative pole (ground)
of the vehicle battery must be disconnected during connection.
B efore reconnecting the negative terminal to the battery, ensure that the device has
been completely connected.
O nly use a volt meter, or a diode test lamp, to check the voltage of the vehicle system
leads, as normal test lamps consume excessive voltage and may thus damage the
vehicle's electronics.
W hen installing the cables, ensure that these are not squashed or scraped on sharp
edges. Use rubber grommets at cable gland points.
• Connect the combined connector of the connecting cable enclosed to the corresponding socket
on the monitor.
• Connect the yellow RCA connector VIDEO 1 IN (yellow wire) to the video output of your playback
device.
• Connect the red RCA connector AUDIO IN to the audio output of your playback device.
• Connect the yellow RCA connector VIDEO 2 IN (white wire) to the video output of another play-
back device or the video output of your reversing camera.
• Connect the black cable GND to the vehicle's ground.
• Connect the red +12 V cable to a connector that only carries +12 V while the ignition is switched
on.
Do not connect this terminal to continuous current, otherwise the on-board battery
could be discharged when the vehicle is parked for a longer period of time.
+12V