Installation - Renkforce T-M1010 Bedienungsanleitung

G Operating Instructions
Auto LCD Monitor 25.6 cm T-M1010
Item no. 1230945
Intended use
The monitor reproduces audio and video signals from externally connected devices in vehicles.
This product is may only be connected to a 12-24 V DC electrical system with the negative pole of
the vehicle battery to the body. The device should only be installed and operated in vehicles with
this on-board voltage type.
The user ensures the protection of the device from dampness and wet by the type of installation.
Any other than the intended use described above might result in product damage and furthermore
cause hazards such as electric shock.
The product as a whole must not be modified or altered.
It is imperative that you follow the safety instructions and all other information contained in this
user manual.
This product complies with the statutory national and European requirements. All company names
and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Monitor
• Remote control with battery
• Mounting bracket
• Sun visor
• Connecting cable set
• Allen key
• Operating instructions
Description of symbols
This symbol informs you about specific risks when handling, operating or using the
product.
The "Arrow" symbol indicates special tips and information about operation.
Safety instructions
F irst read the complete user manual as it contains important information on using the
product.
I n case of damage caused by non-observance of these operating instructions, the
warranty gets void! We are not liable for any consequential damage!
W e are not liable for property damage or injuries caused by improper use or non-
observance of safety instructions! Such circumstances will void the warranty!
• Please ensure correct starting up of the unit. Please follow the operating instruc-
tions.
• Using the monitor to play films etc during the journey is only allowed for passengers
in many countries. The driver should not be distracted by this. Please familiarize
yourself about the statutory regulations of your country before installation.
• Only a 12-24 DC supply network (negative pole of the battery to the body of the vehicle)
may be used as voltage source. Never connect the device to another voltage supply.
• The unauthorized conversion and/or changing of the product is not permitted for
safety reasons.
• Do not expose the device to any extreme temperatures, dripping or spray water,
strong vibrations as well as high mechanical loads.
• Check the device and connection lines from time to time for damage. If the device
shows any damage discontinue operation. Disconnect the device from the power
supply and bring it to a specialist workshop.
• Use the product in temperate climates only, do not use in the tropics.
• This product is not a toy, keep it out of the reach of children. Children cannot recog-
nize the dangers that may arise when handling electrical devices.
• Do not carelessly discard packaging material. It poses a potential danger if children
use it as a toy.
• Also observe the safety instructions and operating instructions of the remaining de-
vices which are connected to the device.
• Observe all other safety instructions in each chapter of these instructions.
• In case of doubts regarding the correct installation or if you have any questions not
being answered in these operating instructions, please contact our technical sup-
port or any other expert.
Inserting/changing the battery for the remote control
Please keep batteries out of reach of children.
Please ensure the correct polarity when inserting the battery.
Remove the battery during log periods of non-use.
L eaking or damaged batteries can cause burns when in contact with skin. You should
thus wear suitable gloves in such a case.
D o not short-circuit batteries. Do not throw into fire. Furthermore it should not be re-
charged. There is a risk of explosion!
The battery of the remote control is protected by the insulation foil before discharging
when first commissioning. Remove this foil before use while pulling it out of the remote
control battery compartment.
• Pull out the battery holder at the back of the remote control.
• Remove the discharged battery and insert a new CR2025 3 V lithium button cell. The correct
polarity is specified on the battery holder.
• Reinsert the battery holder into the remote control.
• If the remote control no longer functions correctly, the battery is discharged and must be re-
placed by a new battery of the same type.

Installation

C arefully select the installation site so that the device does not affect the normal driv-
ing of the driver or distracts him from traffic situations.
N o parts should be installed in the range of the airbag since this can lead to passenger
injuries in the case of an accident.
C hanges to the vehicle which are necessary due to the installation of the monitor or
other components, must always be designed in such a way that they do not lead to
any impairment of road safety or the constructive stability of the car. The operating
license already expires with many cars when sawing out a sheet metal part.
M ake sure that no electric cables, brake lines, the fuel tank are not damaged before
completing the fixing holes.
W hen installing the monitor please take into account the accident risk which can
result from torn off devices in the event of an accident. Therefore securely attach it to
a place where it cannot put passengers at risk.
• Please search for a suitable installation area.
• Remove both knurled screws and both Allen screws on the mounting bracket and remove the
mounting bracket from the monitor.
• If the sun visor is not needed it can be removed from the front of the housing.
• Mark the holes for the attachment screws of the mounting bracket at the installation space.
The assembly bracket can be used as a template.
• Fasten the mounting bracket with matching screws that are suitable for the mounting surface.
• Reattach the monitor with the four screws to the mounting bracket, set the desired angle and
tighten the screws at the mounting bracket.
Connection
The electrical connection should only be carried out by specialists.
T he vehicle battery must be disconnected when connecting the negative pole (mass)
to avoid short circuits and damage to the device resulting from this.
F irst connect the negative pole of the battery when you have fully connected the de-
vice and checked the connection.
O nly use a voltmeter or a diodes test lamp to check the voltage at the on-board volt-
age lines since normal test lamps consume excessive voltage and can damage the
on-board electronics.
D o not squash or rub the cables on sharp edges when laying. Use rubber grommets at
the implementation points.
• Connect the cable provided with the connector on the monitor.
• Connect the yellow V1 RCA jack to the video output of your playback device.
• Connect the white AUDIO1 RCA jack to the audio output of your playback device which is con-
nected to the V1 RCA jack.
• Connect the yellow V2 RCA jack to the video output of an additional playback device or to the
video output of your rear view camera.
• Connect the white RCA jack AUDIO2 to the audio output of your playback device which is con-
nected to the V2 RCA jack.
• Connect the black GND cable to the vehicle ground.
• Connect the red cable +12/24 V to a connection which only carries voltage switched on ignition.