Kärcher HD 5/13 Classic Bedienungsanleitung Seite 11

Symbols on the device
Do not aim the high-pressure jet at persons,
animals, live electrical equipment or the de-
vice itself.
Protect the device against frost.
According to applicable regulations, the de-
vice must never be used with the drinking
water network without a system separator.
Ensure that the connection to your house
water system, with which the high-pressure
cleaner is operated, is equipped with a sys-
tem separator according to EN 12729 type
BA. Water that has flowed through a system
separator is classified as undrinkable. Al-
ways connect the system separator to the
water inlet and never directly to the device.
WARNING
The high nozzle outlet speed of the high-
pressure water jet results in a high noise lev-
el that can cause discomfort or hearing dam-
age (e.g. tinnitus) to persons in the
immediate vicinity. A continuously high
noise level can result in deafness.
● Wear the prescribed personal protective
equipment.
● High noise levels can impair vocal com-
munication and impair or prevent your
ability to perceive acoustic warning sig-
nals. Never work alone. A second per-
son must be present outside the work
area.
Description of the device
Illustration A
Power switch
1
Push handle
2
Cable hook
3
Trigger gun storage clip
4
Hose holder
5
Fasteners for handle
6
Cover
7
Accessory storage
8
Water outlet
9
Water inlet
10
Castor
11
Adapter
12
Oil level window
13
Oil drain screw
14
Oil fill screw
15
Screw connection part
16
Nozzle
17
Spray lance
18
Trigger gun
19
Safety lever
20
10
Trigger
21
High pressure hose
22
DANGER
Danger of injury from electric shock
Only allow authorised technical specialists to install the
water supply, electrical connections and high-pressure
network.
Unpacking
1. Check the contents of the package when unpacking.
2. Notify the dealer immediately in the case of shipping
damage.
Colour coding
● Control elements for the cleaning process are yel-
low.
Installing accessories
1. Fix the nozzle onto spray lance with screw connec-
tion part.
2. Connect the spray lance to the trigger gun.
3. Connect high pressure hose to water inlet and trig-
ger gun.
Illustration B
4. Connect the adapter to the water inlet.
Connection to a water line
WARNING
Health risk from return flow of contaminated water
into the drinking water network.
Observe the regulations of your water supply company.
According to applicable regulations, the device must
never be used with the drinking water network without a
system separator. Use a system separator from
KÄRCHER or a system separator as per EN 12729
Type BA. Water that has flowed through a system sep-
arator is classified as undrinkable. Always connect the
system separator to the water supply and never directly
to the water connection on the device.
1. Check the feed pressure, input temperature and in-
put amount of the water supply. See the "Technical
data" section for the requirements.
2. Connect the system separator and water connection
of the device with a hose (minimum length 7.5 m,
minimum diameter 1").
The supply hose is not included in the scope of de-
livery.
3. Open the water inlet.
Suck water from the container
1. Screw the suction hose (order number 4.440-207.0)
and filter (order number 4.730-012.0) onto the water
connection.
2. Vent the device.
Vent the device
1. Unscrew the nozzle from the spray lance.
2. Allow the device to run until the escaping water is
free of air bubbles.
3. In the case of venting problems, allow the device to
run for 10 seconds and then switch it off. Repeat the
procedure several times.
4. Switch off the device.
5. Screw the nozzle back in place.
English
Initial startup
Initial startup
Water connection