Herunterladen Diese Seite drucken

Scheppach WDT30 Originalbetriebsanleitung Seite 21

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Installing the castors (5) (fig. 4)
• Press the four castors (5) into the holes in the castor
mounts (5a).
Installing the machine head (2) (fig. 5)
• Place the machine head (2) on the stainless steel
container (8). Secure the machine head (2) with the
locking hooks (3). When installing the machine head
(2), ensure that the locking hooks (3) latch into place
correctly.
Installing the foam filter (d) (fig. 6)
Never use the device without filter! Always ensure that
the filters are correctly fitted.
• Installing the foam filter (d):For wet vacuuming, slide
the foam filter (d) provided over the filter basket with
safety float valve (13).
Installing the paper filter bag (c) (fig. 7)
It is recommended to use an additional paper filter bag
(c) when vacuuming fine, dry dirt.
• Slide the paper filter bag (c) over the suction opening
in the stainless steel container (8). The paper filter
bag (c) is only suitable for dry vacuuming. The paper
filter bag (c) makes it easier to dispose of the dust
collected.
Installing the extraction hose (a) (fig. 8)
Connect the suction hose (a) to the corresponding port,
depending on the desired use, on the wet and dry vac-
uum.
Vacuuming (fig. 8):
Connect the suction hose (a) to the suction hose port
(9). To do so, slide the end of the suction hose (a) with
the two nipples into the suction hose port (9) (A). Insert
the two nipples into the recesses. Once the suction
hose (a) is fully inserted, turn it clockwise (B).
Blowing (fig. 9):
Connect the suction hose (a) to the blowing function
connection port (12). Slide the end of the suction hose
(a) with the two nipples into the blowing function con-
nection port (12). Insert the two nipples into the recess-
es. Once the suction hose (a) is fully inserted, turn it
clockwise.
Installing the plastic extension tubes (b), suction
hose (a) and nozzles (e/f) (fig. 10)
• Assemble the plastic extension tubes (b) by pushing
them together.
• Connect the assembled plastic extension tubes with
the bent end of the suction hose (a).
• Fit the floor nozzle (e) or joint nozzle (f) to the other
end of the assembled plastic extension tubes (b).
10. Start up
Warning! Switch the device off if liquid or foam
emerges with the exhaust air during wet vacuum-
ing.
Switching on/off (fig. 11)
Press the on/off switch (10):
• Switch setting 0:Off
• Switch setting I:On
Dry vacuuming
Use the paper filter bag (c) for dry vacuuming.
Wet vacuuming
Use the foam filter (d) for wet vacuuming. Ensure that
the foam filter (d) is correctly fitted.
If the stainless steel container (8) is full, the safety float
valve (13) closes the suction port and suction operation
is interrupted.
m Attention!
The device is not suitable for vacuuming flammable
liquids. For wet vacuuming, use the only the foam filter
(d) provided.
Water drain plug (fig. 12)
The stainless steel container (8) is equipped with
a water drain plug (7) in order to make it easier to
drain. Open the water drain plug (7) by turning it coun-
ter-clockwise and drain out the liquid.
11. Electrical connection
The electrical motor installed is connected and ready
for operation. The connection complies with the appli-
cable VDE and DIN provisions.
The customer's mains connection as well as the ex-
tension cable used must also comply with these reg-
ulations.
www.scheppach.com
GB | 21

Werbung

loading

Diese Anleitung auch für:

5807707986