Jig Saw Safety Warnings - Makita 4328 Betriebsanleitung

ENGLISH
(Original instructions)
1 Cutting action changing lever
2 Switch trigger
3 Lock button
4 Speed adjusting dial
5 Blade holder
6 Bolt
7 Hex wrench
8 Blade
9 Roller
10 Hook
SPECIFICATION
Model
Length of stroke
Blade type
Wood
Max. cutting
capacities
Mild steel
Strokes per minute (min
Overall length
Net weight
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for the sawing of wood, plastic and
metal materials. As a result of the extensive accessory
and saw blade program, the tool can be used for many
purposes and is very well suited for curved or circular
cuts.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
6
Explanation of general view
11 Retainer
12 Base
13 Dust cover
14 Cutting line
15 Edge
16 Graduation
17 Starting hole
18 Hose
19 Steel base type
20 Rip fence (Guide rule)
4326
18 mm
65 mm
6 mm
–1
) 3,100
217 mm
(Steel base type)
223 mm
(Aluminum base type)
1.8 kg
(Steel base type)
1.9 kg
(Aluminum base type)
4327
18 mm
B type
65 mm
6 mm
500 – 3,100
217 mm
(Steel base type)
223 mm
(Aluminum base type)
1.8 kg
(Steel base type)
1.9 kg
(Aluminum base type)

JIG SAW SAFETY WARNINGS

1. Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
ENE019-1
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
ENF002-2 3. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
4. Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
5. Do not cut oversize workpiece.
6. Check for the proper clearance beyond the work-
piece before cutting so that the blade will not
strike the floor, workbench, etc.
GEA010-1
7. Hold the tool firmly.
8. Make sure the blade is not contacting the work-
piece before the switch is turned on.
9. Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
only when hand-held.
21 Aluminum base type
22 Guide facing
23 Fence guide
24 Threaded knob
25 Pin
26 Anti-splintering device
27 Protrusions
28 Aluminum base
29 Cover plate
4328
18 mm
65 mm
6 mm
500 – 3,100
217 mm
1.8 kg
/II
4329
18 mm
65 mm
6 mm
500 – 3,100
223 mm
1.9 kg
GEB016-3