Charging Usb Devices; Cleaning, Storage And Maintenance; Contact Information - APA 16444 Bedienungsanleitung

two minutes until you start the next attempt. After
the third unsuccessful start attempt, do not make an-
other attempt, but check your vehicle for faults.
7. Disconnect the jumper cable from the powerpack.
8. Then remove the pole clamps from the vehicle battery.
Recharge the power pack. Recharge the power pack.
Figure 2:
Smartbox
indicator light
6.4.1 POSSIBLE ERRORS DURING JUMP START
The control lamp of the Smartbox does not shine green
permanently:
• The terminal clamps have no contact or poor
contact to the battery callipers
 Clean the battery poles and reattach the terminal
clamps
• The battery of the Powerpack is not adequately
charged
 Charge the battery
• The current required for the jump start exceeds the
possibilities of the Powerpack
 Use a Powerpack with greater performance
6. 5 USING THE LED LIGHT / SIGNAL LAMP
To switch on the continuous light of the LED light (posi-
tion 7 in the overview), hold down the switch (position 1
in the overview) of the Powerpack for approx. 3 seconds.
Then, by pressing the switch again, you can switch on the
following light functions one after the other: Fast flash-
ing - SOS - OFF

6.6 CHARGING USB DEVICES

If your USB device has a USB-C port, you can use the
supplied USB-C cable for charging. For other connections,
use a cable suitable for your device. These instructions
describe how to use the supplied USB-C charging cable.
Insert the USB-A plug into the USB2 output (position 5 in
the overview) of the Powerpack. The USB-C plug, connect
to your USB device. Press the switch (position 1 in the
overview) of the Powerpack to start the charging process.
The display shows the charging voltage and the charging
current (position 16 in the overview). If your USB device is
designed for the Quick Charge (QC3.0) standard, you can
connect it to the USB3 output (position 6 in the overview)
10
for a faster charging process. Press the switch (position 1
in the overview) of the Powerpack to start the charging
process. The display shows the charging voltage and the
charging current (position 15 in the overview). If your
USB device is suitable for inductive charging, place it on
the inductive charging zone (position 3 in the overview)
and switch on the Powerpack with the switch. The
charging process starts automatically. After charging,
first disconnect the charging cable from the Powerpack,
then remove the charging cable from your USB device.

7. CLEANING, STORAGE AND MAINTENANCE

7.1 CLEANING
Only clean the Powerpack with a soft cloth and do not use
any aggressive cleaning agents or solvents. Never allow
liquids to ingress into the housing.
7.2 STORAGE
When it is not in use, the Powerpack should be stored in
a dry place. Do not expose the Powerpack to moisture,
oil, dust, dirt, high temperatures, excessive vibrations or
mechanical stresses. Always disconnect the jump lead
from the Powerpack before storage to ensure that no
short circuits can occur between the terminal clamps.
7.3 MAINTENANCE
When the Powerpack is not in use, recharge it once it
reaches a battery capacity of 25%.
8. NOTES REGARDING ENVIRONMENTAL
PROTECTION
The packaging is made up of environmental-
ly friendly materials which may be disposed
of via your local recycling points. Do not put
electrical devices into the household waste.
Electronic and electrical devices must be
collected separately and sent for environmen-
tally friendly recycling. Contact your commu-
nity or town administration for information
regarding the disposal of electrics.

9. CONTACT INFORMATION

EAL GmbH
Otto-Hausmann-Ring 107
42115 Wuppertal, Germany
+49 (0)202 42 92 83 0
+49 (0) 202 42 92 83 – 160
info@eal-vertrieb.com
www.eal-vertrieb.com