Das presswerkzeug besitzt einen automatischen rücklauf, der den kolben nach erreichen des max. betriebsüberdruckes
automatisch in die ausgangslage zurückfährt. (36 Seiten)
Seite 3
All manuals and user guides at all-guides.com Bedienungsanleitung/ Instruction Manual SDK32 / SDK32P33 / SDK32P33M Bild/pic. 1 SDK32P33M Cutting head Operating pressure: 700 bar max. Cutting-Ø: 32 mm max. Cu, Al 304711CX142 batch# e.g. 304711 datecode e.g. „-CX“ for year 2009, month Sept.
All manuals and user guides at all-guides.com Bedienungsanleitung SDK32 / SDK32P33 / SDK32P33M Inhaltsangabe Einleitung Garantie Beschreibung der hydraulischen Kabelschere 3.1 Beschreibung der Komponenten 3.2 Beschreibung des Schneidvorganges Hinweise zum bestimmungsgemäßen Gebrauch 4.1 Bedienung des Gerätes 4.2 Erläuterung des Anwendungsbereiches 4.3 Wartungshinweise...
All manuals and user guides at all-guides.com Bedienungsanleitung SDK32 / SDK32P33 / SDK32P33M 1. Einleitung Vor Inbetriebnahme Ihres Schneidkopfes lesen Sie sich die Bedienungsanleitung sorgfältig durch. • Benutzen Sie dieses Werkzeug ausschließlich für den bestimmungsgemäßen Gebrauch. • Das Trennen von Kabeln/Leitern mit Hilfe dieses Werkzeuges darf nur spannungsfrei durch eine elektrotechnisch unterwiesene Person erfolgen.
All manuals and user guides at all-guides.com Bedienungsanleitung SDK32 / SDK32P33 / SDK32P33M 3.2 Beschreibung des Schneidvorganges Bei Schneidvorgängen nach dem Scherenprinzip wird das Kabel in die geöffneten Schneidbacken (Bild1.3 und 1.4) des Schneidkopfes (Bild 1.1) eingelegt oder der Schneidkopf so an das Kabel angelegt, sodaß sich die Lage des Schneidkopfes während der gesamten Schneiddauer nicht ändert.
All manuals and user guides at all-guides.com Bedienungsanleitung SDK32 / SDK32P33 / SDK32P33M Sollten andere Materialien geschnitten werden müssen, ist eine Rücksprache mit dem Werk zwingend erforderlich. Vor Arbeitsbeginn ist ein spannungsfreier Zustand des zu schneidenden Kabels sicherzustellen. Achtung Es dürfen keine unter Spannung stehenden Teile geschnitten werden.
Seite 10
All manuals and user guides at all-guides.com Instruction Manual SDK32 / SDK32P33 / SDK32P33M Index Introduction Warranty Description of the hydraulic cutting tool 3.1 Description of the components 3.2 Description of the cutting cycle Remarks in respect to the determined use 4.1 Operation of the units...
All manuals and user guides at all-guides.com Instruction Manual SDK32 / SDK32P33 / SDK32P33M 2. Warranty If the tool is operated according to its intended use and the regular maintenance services are observed our warranty is 24 months from the time of delivery. Worn-out parts resulting from its intended use are excluded.
All manuals and user guides at all-guides.com Instruction Manual SDK32 / SDK32P33 / SDK32P33M 4.1 Operation of the unit 1. Roll out the hose completely. 2. Connect the cutting head (pic.1.2) to the high pressure hose. 3. Bring the cutting head into a proper cutting position. The blades should cut the cable in a vertical position to avoid undesired shearing forces.
SDK32 / SDK32P33 / SDK32P33M Attention Have the power tool repaired by a qualifi ed expert or by a Klauke Service Center (ASC). 4.4 Remarks which (spare) parts are allowed to be changed by the customer. Within the warranty period the customer is not allowed to make repairs on their own. Do not remove parts such as screws and other components.
Gustav Klauke GmbH • Auf dem Knapp 46 • D-42855 Remscheid Telefon ++49 +2191-907-0 • Telefax ++49 +2191-907-141 • www.klauke.textron.com...
Seite 17
Vmontuju alebo ktoreho sucastou naše vyrobky su nebude ako celok vratane vyrobku, ktory je predmetom tejto deklaracie, vyhovovat zakonnym predpisom. Remscheid, den 29.05.2012 ___________________________________________ Dipl.-Ing. Joh.-Christoph Schütz, CE-Beauftragter Gustav Klauke GmbH • Auf dem Knapp 46 • D-42855 Remscheid Telefon ++49 +2191-907-0 • Telefax ++49 +2191-907-141 • www.klauke.textron.com...