Makita DLS600RTE Betriebsanleitung Seite 20

Lighting up the lamp
CAUTION:
This is not a rainproof light. Do not
wash the light in water or use it in a rain or a wet
area. Such a conduct can cause an electric shock
and fume.
CAUTION:
Do not touch the lens of the light, as
it is very hot while it is lighted or shortly after it is
turned off. This may cause a burn to a human body.
CAUTION:
Do not apply impact to the light,
which may cause damage or shorted service time to it.
CAUTION:
Do not keep casting the beam of
the light to your eyes. This can cause your eyes to
be hurt.
CAUTION:
Do not cover the light with clothes,
carton, cardboard or similar objects while it is
lighted, which can cause a fire or an ignition.
CAUTION:
Do not look in the light or see the
source of light directly.
To turn on the lamp, press the upper position (I) of the
switch. To turn off the lamp, press the lower position (0)
of the switch.
► Fig.28: 1. Lamp 2. Lamp switch
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
NOTE: Be sure to turn off the switch as turning on the
switch consumes the battery power.
Laser beam action
CAUTION:
Never look into the laser beam.
Direct laser beam may injure your eyes.
To turn on the laser beam, press the upper position (I)
of the switch. To turn off the laser beam, press the lower
position (0) of the switch.
► Fig.29: 1. Laser switch
NOTE: Be sure to turn off the switch as turning on the
switch consumes the battery power.
Laser line can be shifted to either the left or right side
of the circular saw blade by turning the adjusting screw
as follows.
► Fig.30: 1. Adjusting screw
1. Loosen the adjusting screw by turning it
counterclockwise.
2. With the adjusting screw loosened, slide the
adjusting screw to the right or left as far as it goes.
3.
Tighten the adjusting screw firmly at the position
where it stops sliding.
NOTE: Laser line is factory adjusted so that it is
positioned within 1 mm from the side surface of the
circular saw blade (cutting position).
NOTE: When laser line appears dim and hard to see
because of direct sunlight, relocate the work area to a
place where there is less direct sunlight.
Aligning the laser line
Align the cutting line on your workpiece with the laser line.
► Fig.31
A) When you want to obtain the correct size on the left
side of workpiece, shift the laser line to the left of the
circular saw blade.
B) When you want to obtain the correct size on the right
side of workpiece, shift the laser line to the right of the
circular saw blade.
ASSEMBLY
WARNING:
switched off and the battery cartridge is removed
before working on the tool. Failure to switch off and
remove the battery cartridge may result in serious
personal injury.
Hex wrench storage
The hex wrench is stored as shown in the figure. When the hex
wrench is needed it can be pulled out of the wrench holder.
After using the hex wrench it can be stored by returning
it to the wrench holder.
► Fig.32: 1. Wrench holder 2. Hex wrench
Installing or removing saw blade
WARNING:
switched off and the battery cartridge is removed
before installing or removing the blade. Accidental
start up of the tool may result in serious personal
injury.
CAUTION:
Use only the Makita hex wrench
provided to install or remove the blade. Failure
to do so may result in overtightening or insufficient
tightening of the hex socket bolt. This could cause
an injury.
To remove the blade, perform the following steps:
1.
Release the stopper pin, and then lock the handle
in the raised position by pushing in the stopper pin.
► Fig.33: 1. Stopper pin
2. Use the hex wrench to loosen the hex socket bolt
holding the center cover by turning it counterclockwise.
Then, raise the blade guard and center cover.
► Fig.34: 1. Center cover 2. Hex socket bolt 3. Hex
wrench 4. Blade guard
3.
Press the shaft lock to lock the spindle and use the hex
wrench to loosen the hex socket bolt clockwise. Then remove
the hex socket bolt of the spindle, outer flange and blade.
► Fig.35: 1. Shaft lock 2. Hex socket bolt 3. Outer flange
4. If the inner flange is removed, install it on the spin-
dle with its blade mounting part facing the blade. If the
flange is installed incorrectly the flange will rub against
the machine.
► Fig.36: 1. Outer flange 2. Saw blade 3. Inner flange
4. Hex socket bolt (left-handed) 5. Spindle
6. Blade mounting part
20 ENGLISH
Always be sure that the tool is
Always be sure that the tool is