Makita CL111DWI Betriebsanleitung Seite 13

Corner nozzle
Fit on the corner nozzle for cleaning corners and crev-
ices of a car or furniture.
► Fig.32: 1. Corner nozzle 2. Cleaner body
Corner nozzle +Extension wand
(Straight pipe)
In tight quarters where the cleaner itself cannot
squeeze in, or in high places hard to reach, use this
arrangement.
► Fig.33: 1. Corner nozzle 2. Extension wand
3. Cleaner body
Cleaning without nozzle
You can pick up powder and dust without nozzle.
► Fig.34
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off before attempting to perform inspec-
tion or maintenance.
After use
When storing or charging the cleaner, lock the nozzle
head, and hang it from a hook available in the market.
► Fig.35
NOTICE:
Putting the cleaner against the wall
without any other support cause the cleaner to
fall down and be damaged.
► Fig.36
Cleaning
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
NOTICE:
Do not blow dust sticking on the
cleaner and filters by air duster. It brings dust into
the housing and causes failure.
NOTICE:
After washing filters, dry them thor-
oughly before use. Insufficiently dried filters may
cause poor suction and shorten the service life of the
motor.
NOTICE:
After cleaning filters and sponge filter,
be sure to re-install them before use. If you use the
cleaner without filters and sponge filter, dust comes
into the motor housing and cause malfunction.
Cleaner body
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening and filter mounting
area.
► Fig.37
Filter
Wash the filter in soapy water when it is clogged with
dust and the cleaner power becomes weak. Dry it out
thoroughly before use.
► Fig.38
Sponge filter
When the sponge filter becomes dirty, clean it as
follows.
1. Remove the filter.
2. Pull out the sponge filter from between the pillars.
3.
Clean the sponge filter by tapping or washing. If
you wash it, dry it out thoroughly before use.
4. Insert the sponge filter from between the pillars
and set it in the original position. Make sure that each
bottom edge of the pillar holds down the sponge filter,
and there is no gap between the sponge filter and suc-
tion opening.
► Fig.39: 1. Sponge filter 2. Bottom edge of pillar
The nozzle cleaning
When the nozzle brush gets dusty, clean up the dust
with sticky.
► Fig.40: 1. Brush
Disposing cleaner
A Li-ion battery is built in this cleaner. Always remove it
before disposing of the cleaner.
Removing built-in battery
CAUTION:
Do not touch the terminals with
any conductive material.
CAUTION:
Avoid storing battery unit in a
container with other metal objects such as nails,
coins, etc.
CAUTION:
Do not expose battery unit to
water or rain.
CAUTION:
Do not disassemble or alter bat-
tery unit.
CAUTION:
The cleaner must be disconnected
from the supply mains when removing the battery.
1. To remove the rear cover, push it in the direction of
the arrow.
► Fig.41: 1. Rear cover
2.
Slide the built-in battery halfway. Disconnect the
lead wires from the battery by slightly moving back the
battery while pressing the connector in the direction of
arrow shown in the figure.
► Fig.42: 1. Connector 2. Lead wires
3. Then slide the battery unit completely.
► Fig.43: 1. Battery unit
4.
Put the removed battery unit in a carton box so
that it is not circuit-shorted.
13 ENGLISH