GUDE Systems Expert Power Control 8032 Serie Anleitung Seite 87

Spezifikationen
port {port_num} watchdog retrybooting show
port {port_num} watchdog bootretries set {num}
port {port_num} watchdog bootretries show
radius
radius {PRIMARY=0|SECONDARY=1} enabled
set <off=0/on=1>
radius {PRIMARY=0|SECONDARY=1} enabled
show
radius {PRIMARY=0|SECONDARY=1} server set
"<dns_name>"
radius {PRIMARY=0|SECONDARY=1} server
show
radius {PRIMARY=0|SECONDARY=1} password
set "{passwd}"
radius {PRIMARY=0|SECONDARY=1} password
hash set "{passwd}"
radius {PRIMARY=0|SECONDARY=1} auth ti-
meout set {num_secs}
radius {PRIMARY=0|SECONDARY=1} auth ti-
meout show
radius {PRIMARY=0|SECONDARY=1} retries set
{num}
radius {PRIMARY=0|SECONDARY=1} retries
show
radius chap enabled set <off=0/on=1>
radius chap enabled show
radius message auth set <off=0/on=1>
radius message auth show
radius default timeout set {num_secs}
radius default timeout show
snmp
snmp port set {ip_port}
snmp port show
snmp snmpget enabled set {OFF=0|ON=1}
snmp snmpget enabled show
snmp snmpset enabled set {OFF=0|ON=1}
snmp snmpset enabled show
snmp snmpv2 enabled set {OFF=0|ON=1}
snmp snmpv2 enabled show
snmp snmpv2 public set "{text}"
snmp snmpv2 public show
snmp snmpv2 private set "{text}"
snmp snmpv2 private show
snmp snmpv3 enabled set {OFF=0|ON=1}
snmp snmpv3 enabled show
snmp snmpv3 username set "{text}"
snmp snmpv3 username show
snmp snmpv3 authalg set {NONE=0|MD5=1|
SHA1=2|SHA256=3|SHA384=4|SHA512=5}
snmp snmpv3 authalg show
snmp snmpv3 privalg set {NONE=0|DES=1|
3DES=2|AES128=3|AES192=4|AES256=5|
AES192*=6|AES256*=7}
snmp snmpv3 privalg show
snmp snmpv3 authpasswd set "{passwd}"
snmp snmpv3 privpasswd set "{passwd}"
snmp snmpv3 authpasswd hash set "{passwd}"
snmp snmpv3 privpasswd hash set "{passwd}"
snmp trap type set {NONE=0|V1=1|V2=2|V3=3}
snmp trap type show
snmp trap receiver {trap_num} set "{dns_name}"
snmp trap receiver {trap_num} show
syslog
syslog enabled set {OFF=0|ON=1}
syslog enabled show
syslog server set "{dns_name}"
syslog server show
system
system restart
87
Expert Power Control 8032
shows port watchdog retry booting state
sets port watchdog retry boot timeout
hows port watchdog retry boot timeout
enters cmd group "radius"
enables radius client
show if radius client enabled
sets radius server address
shows radius server address
sets radius server shared secret
sets radius server crypted shared secret
sets server request timeout
shows server request timeout
sets server number of retries
shows server number of retries
enables CHAP
shows if CHAP is enabled
enables request message authentication
shows if request message authentication is enab-
led
sets default session timeout (when not returned as
Session-Timout Attribute)
shows default session timeout
enters cmd group "snmp"
sets SNMP UDP port
shows SNMP UDP port
enables SNMP GET cmds on/off
show if SNMP GET cmds are enabled
enables SNMP SET cmds on/off
show if SNMP SET cmds are enabled
enables SNMP v2 on/off
show if SNMP v2 is enabled
enables SNMP v3 on/off
show if SNMP v3 isenabled
sets SNMP v2 public cummnity
shows SNMP v2 public community
sets SNMP v2 private community
shows SNMP v2 private community
sets SNMP v3 username
shows SNMP v3 username
sets SNMP v3 authentication
show SNMP v3 authentication algorithm
sets SNMP v3 privacy algorithm
show SNMP v3 privacy algorithm
sets SNMP v3 authentication password
sets SNMP v3 privacy password
sets SNMP v3 authentication hashed password
sets SNMP v3 privacy hashed password
sets type of SNMP traps
show SNMP trap type
sets address and port of SNMP trap receiver
{trap_num}
show address and port of SNMP trap receiver
{trap_num}
enters cmd group "syslog"
enables syslog msgs on/off
show if syslog enabled
sets address of syslog server
shows address of syslog server
enters cmd group "system"
restarts device
© 2021 GUDE Systems GmbH