Bosch GOP 300 SCE Professional Originalbetriebsanleitung Seite 16

All manuals and user guides at all-guides.com
OBJ_BUCH-1271-006.book Page 16 Friday, April 29, 2016 9:48 AM
16 | English
Selecting the Application Tool/Accessory
Accessory
HCS wood seg-
ment saw blade*
BIM segment saw
blade*
HCS plunge cut
saw blades,
wood*
BIM plunge cut
saw blades,
metal*
BIM plunge cut
saw blade, wood
and metal*
HM-Riff segment
saw blade*
HM-Riff delta
plate*
Scraper, rigid*
Scraper, flexible* Silicone and other
Base plate for
sanding, series
Delta 93 mm*
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
Mounting/Replacing the Application Tool/Accessory
(GOP 250 CE)
If required, remove an already mounted application tool/ac-
cessory.
For removing the application tool/accessory, loosen the
screw 7 with the hex key 8 and remove the application
tool/accessory.
Mount the requested application tool/accessory (e.g. plunge
cut saw blade 6) in such a manner on the tool holder 4 that the
offset faces downward (see illustration on the graphics page;
marking on the application tool/accessory is readable from
above).
Turn the application tool/accessory to a position favourable
for the respective job, and allow it to engage into the cams of
the tool holder 4. 12 different positions are possible, each
offset by 30°.
1 609 92A 2PJ | (29.4.16)
For more intermediate positions, the adapter 9 (accessory)
can be used: Allow the adapter to engage with the smooth
Material
side onto the cams of the tool holder 4 (see illustration on the
Wooden materials,
graphics page). Position the application tool/accessory onto
plastic
the adapter in any position.
Wooden materials,
Fasten the application tool/accessory with bolt 7. Tighten the
plastic, non-ferrous
bolt with hex key 8 until the spring washer of the bolt faces
metals
flush against the application tool/accessory.
Wooden materials,
 Check the tight seating of the application tool/accesso-
plastic, gypsum and
ry. Incorrect or not securely fastened application tools/ac-
other soft materials
cessories can come loose during operation and pose a haz-
Metal (e. g. unhard- ard.
ened nails, screws,
Mounting/Replacing the Application Tool/Accessory
smaller profiles),
(GOP 300 SCE)
non-ferrous metals
If required, remove an already mounted application tool/
Wood, metal, non-
accessory.
ferrous metals
For this, open the SDS lever 12 to the stop (not further) and
remove the application tool.
Grouting joints, soft
Mount the requested application tool/accessory (e.g. plunge
wall tiles, glass-fibre
cut saw blade 6) in such a manner on the tool holder 4 that the
reinforces plastic
offset faces downward (see illustration on the graphics page;
and other abrasive
marking on the application tool/accessory is readable from
materials
above).
Turn the application tool/accessory to a position favourable
for the respective job, and allow it to engage into the cams of
the tool holder 4. 12 different positions are possible, each
Carpets, coverings
offset by 30°.
Close SDS lever 12 so that it faces against the housing of the
power tool.
 Check the tight seating of the application tool/accesso-
ry. Incorrect or not securely fastened application tools/ac-
elastic materials
cessories can come loose during operation and pose a haz-
ard.
Mounting/Replacing a Sanding Sheet on the Sanding
Depends on sanding
Plate
sheet
The sanding plate 10 is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 11, free the Velcro back-
ing of the sanding plate 10 from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet 11 flush alongside one edge of the
sanding plate 10, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 11, grasp it at one of the tips and
pull it off from the sanding plate 10.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
Bosch Power Tools