Parts Description - Makita DLS211PT2U Betriebsanleitung

7. Do not operate the wireless unit in places
where automated devices are nearby. If oper-
ated, automated devices may develop malfunction
or error.
8. Do not operate the wireless unit in places
under high temperature or places where
static electricity or electrical noise could be
generated.
9. The wireless unit can produce electromagnetic
fields (EMF) but they are not harmful to the
user.
10. The wireless unit is an accurate instrument. Be
careful not to drop or strike the wireless unit.
11. Avoid touching the terminal of the wireless
unit with bare hands or metallic materials.
12. Always remove the battery on the product
when installing the wireless unit into it.
13. When opening the lid of the slot, avoid the
place where dust and water may come into the
slot. Always keep the inlet of the slot clean.
14. Always insert the wireless unit in the correct
direction.
15. Do not press the wireless activation button
on the wireless unit too hard and/or press the
button with an object with a sharp edge.
16. Always close the lid of the slot when
operating.
17. Do not remove the wireless unit from the slot
while the power is being supplied to the tool.
Doing so may cause a malfunction of the wireless
unit.

PARTS DESCRIPTION

► Fig.2
1 Slide pole
5 Sub base
9 Kerf board
13 Blade guard
17 Adjusting screw (for
lower limit position)
21 Lock lever (for turn base)
► Fig.3
1 Stopper pin (for carriage
elevation)
5 Switch trigger
9 Switch (for laser line)
13 Wireless activation
button
17 0° adjusting bolt (for
bevel angle)
21 Releasing lever (for 48°
bevel angle)
2 Stopper pin (for carriage
sliding)
6 Turn base
10 Blade case
14 Knob (for bevel angle)
18 Adjusting bolt (for maxi-
mum cutting capacity)
22 Releasing lever (for turn
base)
2 Hose (for dust
extraction)
6 Lock-off button
10 Battery indicator
14 Wireless activation lamp
18 Pointer (for bevel angle)
- -
18. Do not remove the sticker on the wireless unit.
19. Do not put any sticker on the wireless unit.
20. Do not leave the wireless unit in a place where
static electricity or electrical noise could be
generated.
21. Do not leave the wireless unit in a place sub-
ject to high heat, such as a car sitting in the
sun.
22. Do not leave the wireless unit in a dusty or
powdery place or in a place corrosive gas
could be generated.
23. Sudden change of the temperature may bedew
the wireless unit. Do not use the wireless unit
until the dew is completely dried.
24. When cleaning the wireless unit, gently wipe
with a dry soft cloth. Do not use benzine, thin-
ner, conductive grease or the like.
25. When storing the wireless unit, keep it in the
supplied case or a static-free container.
26. Do not insert any devices other than Makita
wireless unit into the slot on the tool.
27. Do not use the tool with the lid of the slot dam-
aged. Water, dust, and dirt come into the slot may
cause malfunction.
28. Do not pull and/or twist the lid of the slot more
than necessary. Restore the lid if it comes off
from the tool.
29. Replace the lid of the slot if it is lost or
damaged.
SAVE THESE INSTRUCTIONS.
3 Vertical vise
7 Pointer (for miter angle)
11 Adjusting screw (for
laser line)
15 Hex wrench
19 Stopper arm
23 Grip (for turn base)
3 Guide fence (upper
fence)
7 Hole for padlock
11 Mode indicator
15 Dust bag
19 45° adjusting bolt (for
bevel angle)
- -
23 ENGLISH
4 Releasing button (for
right side bevel angle)
8 Miter angle scale
12 Range adjustment screw
(for laser line)
16 Sub fence
20 Battery cartridge
- -
4 Guide fence (lower
fence)
8 Lid (for wireless unit)
(For DLS211 only)
12 Check button
16 Bevel angle scale
20 Latch lever (for bevel
angle)
- -