Intended Use - Makita DLS211PT2U Betriebsanleitung

Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
Wear safety glasses.
To avoid injury from flying debris, keep
holding the saw head down, after making
cuts, until the blade has come to a com-
plete stop.
When performing bevel cut, first turn the
2
1 3
knob counterclockwise and then tilt the
carriage. After that, turn the knob clockwise
to tighten.
When performing slide cut, first pull car-
riage fully and press down handle, then
push carriage toward the guide fence.
Hold down the releasing button when tilting
the carriage to the right.
Engage the stopper lever when cutting a
base board in 45° miter angle.
Do not place hand or fingers close to the
blade.
Never look into the laser beam. Direct laser
beam may injure your eyes.
Do not install the horizontal vise to the
same direction as the miter cutting. (This
symbol is applied on the horizontal vise)
Only for EU countries
Ni-MH
Due to the presence of hazardous com-
Li-ion
ponents in the equipment, waste electrical
and electronic equipment, accumulators
and batteries may have a negative impact
on the environment and human health.
Do not dispose of electrical and electronic
appliances or batteries with household waste!
In accordance with the European Directive on
waste electrical and electronic equipment and on
accumulators and batteries and waste accumu-
lators and batteries, as well as their adaptation to
national law, waste electrical equipment, batteries
and accumulators should be stored separately
and delivered to a separate collection point for
municipal waste, operating in accordance with the
regulations on environmental protection.
This is indicated by the symbol of the crossed-
out wheeled bin placed on the equipment.
BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /

Intended use

The tool is intended for accurate straight and miter
cutting in wood. With appropriate saw blades, aluminum
can also be sawed.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-3-9:
Model DLS211
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model DLS212
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
WARNING:
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-3-9:
Model DLS211
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DLS212
Vibration emission (a
Uncertainty (K) : 1.5 m/s
19 ENGLISH
DC18SH / DC18WC
) : 95 dB (A)
pA
) : 103 dB (A)
WA
) : 95 dB(A)
pA
) : 103 dB (A)
WA
Wear ear protection.
The noise emission during actual
Be sure to identify safety mea-
2
) : 2.5 m/s or less
h
2
2
) : 2.5 m/s or less
h
2