Parts Description; Bench Mounting; Functional Description - Makita LS002G Betriebsanleitung

PARTS DESCRIPTION

► Fig.2
1 Hex wrench
5 Wireless activation
button
9 Blade guard
13 Releasing lever (for turn
base)
17 Miter angle scale
21 Releasing lever (for right
side bevel angle)
25 Right bevel angle scale
29 Lid (for wireless unit)
► Fig.3
1 Hole for padlock
5 Battery cartridge
9 Releasing lever (for 48°
bevel angle)
INSTALLATION

Bench mounting

WARNING:
Ensure that the tool does not
move on the supporting surface. Movement of the
miter saw on the supporting surface while cutting may
result in loss of control and serious personal injury.
1. Fix the base to a level and stable surface, screw-
ing with the bolts. This helps to prevent from tipping and
possible injury.
► Fig.4: 1. Bolt 2. Mounting hole
2. Turn the adjusting bolt clockwise or counterclock-
wise so that it comes into a contact with the floor sur-
face to keep the tool stable.
► Fig.5: 1. Adjusting bolt
Installing the dust extraction hose
Connect the dust extraction hose to the tool as
illustrated.
Make sure that the elbow and the sleeve fit properly to
the ports of the tool.
► Fig.6: 1. Dust extraction hose 2. Elbow 3. Sleeve
4. Port
To remove the elbow from the port, pull the elbow while
pressing down the lock button.
To remove the sleeve from the port, turn it clockwise
and then pull it apart.
► Fig.7: 1. Elbow 2. Lock button 3. Sleeve 4. Port
2 Adjusting bolt (for maxi-
mum cutting capacity)
6 Wireless activation lamp
10 Kerf board
14 Adjusting bolt (for turn
base)
18 Turn base
22 45° adjusting bolt (for
right bevel angle)
26 Pointer (for right bevel
angle)
- -
2 Switch trigger
6 Dust extraction hose
10 45° adjusting bolt (for left
bevel angle)
3 Adjusting screw (for
lower limit position)
7 Vacuum button
11 Grip (for turn base)
15 Guide fences
19 Sub base
23 0° adjusting bolt (for
bevel angle)
27 Stopper pin (for carriage
sliding)
- -
3 Lock-off button
7 Left bevel angle scale
11 Shaft lock
FUNCTIONAL
DESCRIPTION
WARNING:
switched off and the battery cartridge is removed
before adjusting or checking the functions on
the tool. Failure to switch off and remove the battery
cartridge may result in serious personal injury from
accidental start-up.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
► Fig.8: 1. Red indicator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
shown in the figure, it is not locked completely.
20 ENGLISH
4 Stopper arm
8 Lamp button
12 Grip dial (for bevel
angle)
16 Pointer (for miter angle)
20 Vertical vise
24 Dust guide
28 Slide pole
-
4 Carry handle
8 Pointer (for left bevel
angle)
12 Dust bag (when replaced
with dust extraction
hose)
Always be sure that the tool is
-