Recording Broadcasts From An External Equipment; Making Timer Recordings On The Television; Recording From Digital/Satellite Receiver Or Decoder; Linked Timer Recordings With External Equipment (Digital/Satellite Receiver)-Ext Link - Panasonic DMR-ES15 Bedienungsanleitung

Recording broadcasts from an external equipment

g
h
* REC
REC MODE
RAM -R -R DL -RW(V) +R +R DL +RW
Preparation
• Insert a disc (➔ page 16).
• When recording a bilingual programme (➔ page 14).
Making timer recordings on the
television
(e.g., of digital broadcasts)
To make a timer recording with your television, connect to a
television with a Q Link function (➔ page 38) that you can use for
setting timer recordings using a fully wired 21-pin Scart cable
(➔ page 8, 9).
1
Make timer programming on the TV.
2
Turn off the unit.
The start and end of recording is controlled by TV.
To stop recording
Press [g].
Note
• When this unit is in EXT LINK standby ("EXT-L" on the unit's
display), recording from TV does not start.
• Programmes are recorded as one title on this unit when the end
time of the earlier timer recording and the start time of the later
timer recording are close to each other.
To divide the titles, go to "Divide Title" (➔ page 31).
RAM
EXT LINK CH
DV IN AV3
EXT LINK g * REC
INPUT
SELECT
EXT LINK
Recording from digital/satellite
receiver or decoder
Preparation
• Connect a digital/satellite receiver or decoder to this unit's input
terminals (➔ page 9).
• When the output signal from the external equipment is NTSC,
change the "TV System" to "NTSC" in the Setup menu
(➔ page 43).
1
While stopped
Press [INPUT SELECT] to select the
input channel for the equipment you
have connected.
e.g., If you have connected to AV2 input terminals, select "AV2".
2
Press [REC MODE] to select the
recording mode.
3
Select the channel on the other
equipment.
4
Press [* REC].
Recording starts.
To skip unwanted parts
Press [h] to pause recording. (Press again to restart recording.)
To stop recording
Press [g].
Linked timer recordings with external
equipment (digital/satellite receiver)–
EXT LINK
To record programmes from a digital/satellite receiver using timer
programming
Preparation
• Make sure you connect the AV2 input terminal of this unit to "VCR
Scart Terminal" of a digital/satellite receiver with a 21-pin scart
cable (➔ page 9).
• Set the "AV2 Input" and "Ext Link" to match the connected
equipment in the Setup menu (➔ page 41).
1
Make timer programming on the
external equipment.
2
Press [EXT LINK].
The unit turns off and "EXT-L" lights on the unit's display to
indicate timer recording standby has been activated.
To cancel the external control
Press [EXT LINK] to stop recording or to cancel linked timer
recording standby.
• In order to prevent accidental operation, press [EXT LINK] to
cancel the setting after recording is finished.
For your reference
• This function does not work with some equipment. Refer to the
equipment's operating instructions.
• The beginnings of recordings may not be recorded correctly in
some cases.
• When "Ext Link" is set to "Ext Link 2", this function does not work if
the input signal is NTSC system.
• When "AV2 Connection" is set to "Decoder", EXT LINK is not
available (➔ page 41).
• Programmes are recorded as one title on this unit when the end
time of the earlier timer recording and the start time of the later
timer recording are close to each other.
To divide the titles, go to "Divide Title" (➔ page 31).
RAM
• While the unit is in EXT LINK standby mode or recording, video
picture is from the AV2 input terminal irrespective of "AV1 Output"
setting.
RQT8318
21
21