Werbung
Verfügbare Sprachen
Verfügbare Sprachen
display.
The meter cho
range ca
an be selected
through
the available r
seconds
.
7.1 Vo
oltage meas
Do not mea
occur.
Always be ca
fingers behin
terminals wh
•
Conn
nect the black t
•
Set t
the rotary sele
. f
for DC measur
•
Conn
nect the test le
•
The
measured valu
•
Whe
n desired, sele
•
Press
s the Hz/DUT
again
n to return to v
Notes:
•
F
For DC-measur
i
ndicated value
•
W
When the meas
"
"OL". Select a h
7.2 Cu
urrent meas
Do not measu
Current measu
10A jack. Whe
followed by a
Always be car
fingers behind
•
For
measuremen
black
k lead to the "C
•
For
measuremen
lead
to the "COM"
•
Set t
the function se
•
Set t
the function se
•
Whe
n the range is
appr
ropriate range.
•
Selec
ct the AC or DC
curre
ent).
•
Conn
nect the test pr
•
Read
d the measured
•
Whe
n desired, sele
•
Press
s the Hz/DUT
again
n to return to v
Notes:
•
F
For DC-current
the indicated va
t
•
The µAmA-rang
T
range is protec
r
•
When measurin
W
break between
b
22.06.20
010
ooses the most
t suitable range
manually by p
ressing the RA
ranges. To retu
urn to auto-ran
surements
sure circuits
where voltag
areful when wo
orking with volt
nd the probe ba
arriers at all tim
hen the meter i
is linked to a c
test lead to the
e COM jack an
ctor to V
for
r AC measurem
rements within
the millivolt-ra
eads to the circ
cuit under test.
ue appears on t
the display.
ect a range ma
nually with the
TY button to se
ee the frequenc
voltage display
y.
rements: when
n a negative po
e is preceded by
y a "-" sign.
sured value is
higher than th
higher range.
surements
ure current in c
circuits with vo
urements: µAm
mA jack max. 4
en measuring c
currents above
10 minutes br
eak between 2
reful when wor
king with volta
d the probe bar
rriers at all tim
ts up to 400m
mA: connect th
COM" jack.
ts up to 10A:
: connect the r
jack.
elector to A
for measureme
elector to mA
or µA
unknown, alwa
ays select the
C range with th
he SELECT bu
robes in series
with the circu
d value from th
he display.
ect a range ma
nually with the
TY button to se
ee the frequenc
voltage display
y.
measurement
ts, when a neg
alue is precede
ed by a "-" sign
ge is protected
against over-c
ted against ov
er-current with
ng above 5A, m
max. 15s contin
2 measureme
nts.
DVM11
00
e for the select
ANG button. Pr
nging press and
ges > 600V CA
tages above 60
mes during me
ircuit which is
d the red test
ments, to V
ange
.
e RANG button
cy or duty cycle
olarity is presen
e selected rang
ltages > 600V
400mA; for me
e 5A, max. 15s
2 measurement
ages above 60V
mes during mea
he red test lead
ed test lead to
ents up to 10A
for
measurement
highest possib
tton (AC = alte
it.
e RANG button
cy or duty cycle
ative polarity i
n.
current with a
h a F10mA 600
nuous measure
8
ted function. W
When desired th
ress multiple ti
imes to scroll
d hold the RAN
NG button for 2
AT III or > 1
000V CAT II
0Vdc or 30Vac
rms. Keep you
easurement. Do
o not touch un
being tested.
lead to the VΩ
Ω jack.
for DC measure
f
ements or to m
n (not in the m
mV
e of the measu
ured voltage. P
nt at the red te
est lead, the
ge limit, the di
splay will show
easurements u
p to 10A use t
s continuous m
easurement
ts.
Vdc or 30Vac r
rms. Keep your
asurement.
d to the "µAm
A" jack and th
the "10A" jac
ck and the blac
A on the 10A ja
ack.
s up to 400mA
A on the µAmA
ble range and lo
ower to the
ernating curren
nt, DC = direct
n.
e of the measu
ured voltage. P
s present at th
he red test lead
F500mA 600V
V fuse, the 10A
0V fuse.
ement followed
d by a 10 minu
Rev
v. 01
he
2
may
ur
used
mV
range)
Press
w
he
r
e
ck
jack.
t
Press
d,
A-
utes
©Vellema
n nv
Werbung
