Velleman DVM1100 Bedienungsanleitung Seite 7

c. Keyp pad
Ke ey
SEL LECT
HOLD/ /LIGHT
V~,
RA ANG
RE EL
Hz/D DUTY V~,
7. Op peration
Risk of electr
Before measur
verify the conn
• Neve er exceed the l
spec ifications for e
• Do n not touch unuse
• Only y use the meter
that might exceed
• Disco onnect the test
chan nge functions.
• Whe n carrying out
that high amplitude
• Alwa ays be careful w
behin nd the probe b
• Do n not measure cu
• Neve er perform resi
Make e sure all capa
"Hold" Function:
Press the e "HOLD/LIGHT
the displ lay. Press agai
"Light" Function:
Press an nd hold the "HO
REL fun nction: (not av
Press the e REL button d
currently y measured va
circuit is s now displayed
shown o n the display w
to quit th his function.
Automat tic battery savi
this func ction switches t
rotate th he function sele
SELECT button for 2 s
Automat tic and manual
When sw witching on the
22.06.20 010
S Symbol
Select resistanc S
Ω Ω
check. c
A mA µA A
S Select DC oran
Po ower-off
D Disables auto p
P Press to enter a
2 seconds to sw 2
Press to enter t P
V , Ω, A,
(press multiple (
mA, µA
P Press and hold
P Press to enter a
Press to start f P
A, mA, µA ( (press multiple
f functions).
ric shock duri ing operation
ring, always m ake sure the m
nections, selec ted function an
imit value for p protection. Thi
ach range of m measurement.
ed terminals w when the meter
r in the indicat ted overvoltage
the indicated c category value
t leads from th he tested circui
measurement s on a TV set o
e voltage pulse es at the test p
when working w with voltages a
barriers at all ti imes during me
urrent in circuit ts with voltage
stance, diode, continuity or c
citors in the cir rcuit are discha
T" button to fr eeze the value
n to resume no ormal operatio
OLD/LIGHT" bu utton for 2 seco
vailable in frequ uency measuri
during measure ement to start
lue is stored a s reference an
d as the differe ence compared
when the mete er is in relative
ing mode:
the meter to b attery saving m
ector to exit sle eep mode. To
econds.
range selectio on:
e meter it will b be in auto-rang
DVM11 00
Des
ce measureme
d AC current.
power-off funct
and exit the da
witch backlight
the manual ran
times to brow wse through the
for 2 seconds
and exit the re
requency/cycli
times to brow wse through the
n. Be very care
meter and/or te
nd range.
s limit value is
r is linked to a
e/installation c
s.
t before rotatin
or switching po
points might da
above 60Vdc o
easurement.
s > 250V
capacitance me
arged.
e onto the disp
on.
onds to activat
ng mode)
the relative m measurement fu
d the display s
d to the referen
measuring mo
mode after ±3
disable this fun
ging mode; the
7
scription
ent, diode test or continuity
tion.
ata hold mode. . Press and hol
t on or off.
nging mode an nd select the ra
e available ran
to return to au uto-ranging mo
elative measure ement function
c ratio measur rement.
e available
eful when meas suring live circu
est probes are not damaged
s listed separat tely in the
circuit which is s being tested.
ategory. Never r measure volt
ng the range s elector in orde
ower circuits, a always rememb
amage the met ter.
or 30Vac rms. K Keep your finge
easurements o on live circuits.
lay. The sym mbol appears o
te and deactiva ate the backligh
unction. The
shows 00.00. E Every change in
nce value. The
ode. Press the REL button ag
0 min. Press H HOLD/LIGHT o
nction, press a nd hold the
e icon is s shown on the
Rev v. 01
d for
ange
ges).
ode.
n.
uits.
and
.
tages
er to
ber
ers
on
ht.
n the
symbol i is
gain
or
©Vellema n nv