Proper Use; Technical Data - EINHELL 43.003.90 Originalbetriebsanleitung

the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
•
Drag, crosscut and miter saw
•
Clamping device
•
Workpiece support (2x)
•
Locking screw
•
Sawdust bag
•
Socket head screw 5mm for workpiece sup-
port (4x)
•
Hex key 5mm
•
Hex key 6mm
•
Original operating instructions
•
Safety instructions

3. Proper use

The drag, crosscut and miter saw is designed
for cross-cutting wood and wood-type materials
which are appropriate for the machine's size. The
saw is not designed for cutting fi rewood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
Anl_TC_SM_2131_2_Dual_SPK9.indb 23
GB
The equipment is to be operated only with suita-
ble saw blades. It is prohibited to use any type of
cutting-off wheel.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impos-
sible to eliminate certain residual risk factors. The
following hazards may arise in connection with
the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut inju-
ries).
•
Kick-back of workpieces and parts of workpi-
eces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if ear-muffs are not used
as necessary.
•
Harmful emissions of wood dust when used
in closed rooms.

4. Technical data

AC motor: ................................220-240 V ~ 50Hz
Power: ................. 1500 W S1 / 1800 W S2 5 min
Idle speed n : ......................................4900 min
0
Carbide saw blade: ...........ø 210 x ø 30 x 2.8 mm
Maximum tooth pitch: ................................. 3 mm
Number of teeth: ............................................ 48
Swiveling range: ........................... -47° / 0° / +47°
Miter cut to the left: .................................0° to 45°
Miter cut to the right: ...............................0° to 45°
Saw width at 90°: ............................ 310 x 62 mm
Saw width at 45°: ............................ 210 x 62 mm
Saw width at 2 x 45°
(double miter cut left): ...................... 210 x 36 mm
Saw width at 2 x 45°
- 23 -
-1
30.09.2021 15:22:51