DeWalt DCD709 Bersetzt Von Den Originalanweisungen Seite 36

EnGLIsH
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Belt Hook and Magnetic Bit Holder (Fig. A)
(Optional Accessories)

WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend objects
from the belt hook. ONLY hang tool's belt hook from a
work belt.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.
IMPORTanT: When attaching or replacing a belt hook or
magnetic bit holder, use only the screw that is provided. Be sure
to securely tighten the screw.
A belt hook 11 and magnetic bit holder
to either side of the tool using only the screw
to accommodate left‑ or right‑handed users. If the hook or
magnetic bit holder is not desired at all, it can be removed from
the tool.
To move belt hook or magnetic bit holder, remove the screw
that holds it in place then reassemble on the opposite side. Be
sure to securely tighten the screw.
Installing a Bit or Accessory into a
Keyless Chuck (Fig. D)

WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and disconnect tool from power source when
changing acces sories.

WARNING: Always ensure the bit is secure before starting
the tool. A loose bit may eject from tool causing possible
personal injury.
Your tool features a keyless chuck
for one‑handed operation of the chuck. To insert a drill bit or
other accessory, follow these steps.
1. Turn tool off and remove battery pack.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve clockwise with
one hand while holding the tool with the other. Your tool is
equipped with an automatic spindle lock mechanism. This
allows you to open and close the chuck with one hand.
Be sure to tighten chuck with one hand on the chuck sleeve and
one hand holding the tool for maximum tightness.
To release the accessory, repeat steps 1 and 2 above.
34
13 can be be attached
12 provided,
12
10 with one rotating sleeve
Speed Selection (Fig. A)
The tool features two speed settings for
greater versatility. nOTE: Do not change speeds when the tool
is running. Always allow the tool to come to a complete stop
before changing speed.
1. To select speed 1 (high torque setting), turn the tool off and
permit it to stop. Slide the speed selector
from the chuck).
2. To select speed 2 (high speed setting), turn the tool off and
permit it to stop. Slide the speed selector
the chuck).
If the tool does not change speeds, confirm that the speed
selection switch is completely engaged in the forward or
back position.
Mode Selection (Fig. A)
The mode selection collar
operating mode depending upon the planned application.
To select, rotate the collar until the desired symbol aligns with
the arrow.
symbol
1–15
Variable Speed Trigger and Forward/Reverse
Control Button (Fig. A, E)
The drill is turned on and off by pulling and releasing the
variable speed trigger
the higher the speed of the drill. Your tool is equipped with
a brake. The chuck will stop as soon as the trigger switch is
fully released.
A forward/reverse control button
direction of the tool and also serves as a lock‑off button.
• To select forward rotation, release the trigger and depress
9
the forward/reverse control button on the right side of
the tool.
• To select reverse, depress the forward/reverse control
button on the left side of the tool.
nOTE: The centre position of the control button locks the tool
in the off position. When changing the position of the control
button, be sure the trigger is released.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
7
7
6 can be used to select the correct
Mode
Drilling
Screwdriving (higher number = greater torque)
Hammerdrilling (DCD709 only)
4 . The farther the trigger is depressed,
5 determines the rotational
back (away
forward (toward