Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GWS 8-125 Professional Originalbetriebsanleitung

OBJ_BUCH-340-007.book Page 25 Tuesday, August 30, 2016 3:35 PM
For cutting stone, it is best to use a diamond cutting disc.
When using the cutting guide with dust extraction protection
guard 21, the vacuum cleaner must be approved for vacuum-
ing masonry dust. Suitable vacuum cleaners are available
from Bosch.
clearly indicated by circular sparking, rotating with the dia-
mond cutting disc.
In this case, interrupt the cutting process and allow the dia-
mond cutting disc to cool by running the machine for a short
time at maximum speed with no load.
Noticeably decreasing work progress and circular sparking
are indications of a diamond cutting disc that has become
dull. Briefly cutting into abrasive material (e. g. lime-sand
brick) can resharpen the disc again.
Information on Structures
Slots in structural walls are subject to the Standard DIN 1053
Part 1, or country-specific regulations.
These regulations are to be observed under all circumstanc-
es. Before beginning work, consult the responsible structural
engineer, architect or the construction supervisor.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
 In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a portable residual current device (PRCD).
When working metals, conductive dust can settle in the in-
terior of the power tool. The total insulation of the power
tool can be impaired.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Please store and handle the accessory(-ies) carefully.
Bosch Power Tools

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Switch on the machine
Bosch's application service team will gladly answer questions
and place the front part
concerning our products and their accessories.
of the cutting guide on
the workpiece. Slide the
In all correspondence and spare parts orders, please always
machine with moderate
include the 10-digit article number given on the nameplate of
feed, adapted to the ma-
the product.
terial to be worked.
Great Britain
For cutting especially
Robert Bosch Ltd. (B.S.C.)
hard material, e. g., con-
P.O. Box 98
crete with high pebble
Broadwater Park
content, the diamond
North Orbital Road
cutting disc can over-
Denham
heat and become dam-
Uxbridge
aged as a result. This is
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
English | 25
1 609 92A 336 | (30.8.16)