Working Advice - Bosch GWS 8-125 Professional Originalbetriebsanleitung

OBJ_BUCH-340-007.book Page 24 Tuesday, August 30, 2016 3:35 PM
24 | English
Restarting Protection
(GWS 11-125 CI/GWS 11-125 CIE/GWS 14-125 CI/
GWS 14-125 CIE/GWS 14-125 CIT/GWS 14-150 CI)
The restarting protection feature prevents uncontrolled re-
starting of the machine after an interruption in the power sup-
ply.
To restart the operation, switch the On/Off switch 4 to the
Off position and start the machine again.
Speed preselection (GWS 11-125 CIE/GWS 14-125 CIE/GWS 14-125 CIT)
The required speed can be preselected with the thumbwheel 3 (also while running).
The data in the following table are recommended values.
Material Application
Metal Removing paint
Wood, metal Brushing, rust removal
Metal, masonry Grinding
Metal Rough grinding
Masonry, stone Cutting

Working Advice

 Exercise caution when cutting slots in structural walls;
see Section "Information on Structures".
 Clamp the workpiece if it does not remain stationary
due to its own weight.
 Do not strain the machine so heavily that it comes to a
standstill.
 After heavily straining the power tool, continue to run
it at no-load for several minutes to cool down the acces-
sory.
 Do not touch grinding and cutting discs before they
have cooled down. The discs can become very hot while
working.
 Do not use the power tool with a cut-off stand.
Rough Grinding
 Never use a cutting disc for roughing.
The best roughing results are achieved when setting the ma-
chine at an angle of 30° to 40°. Move the machine back and
forth with moderate pressure. In this manner, the workpiece
will not become too hot, does not discolour and no grooves
are formed.
Flap Disc
With the flap disc (accessory), curved surfaces and profiles
can be worked.
Flap discs have a considerably higher service life, lower noise
levels and lower sanding temperatures than conventional
sanding sheets.
1 609 92A 336 | (30.8.16)
Reduced starting current
(GWS 11-125 CI/GWS 11-125 CIE/GWS 14-125 CI/
GWS 14-125 CIE/GWS 14-125 CIT/GWS 14-150 CI)
The electronic reduced starting current limits the power con-
sumption when switching the tool on and enables operation
from a 13 ampere fuse.
Constant Electronic Control
(GWS 11-125 CI/GWS 11-125 CIE/GWS 14-125 CI/
GWS 14-125 CIE/GWS 14-125 CIT/GWS 14-150 CI)
Constant electronic control holds the speed constant at no-
load and under load, and ensures uniform working perfor-
mance.
Accessory
Sanding disc
Cup brush, sanding disc
Grinding disc
Grinding disc
Cutting disc and cutting guide
(Cutting masonry/stone is permitted only with use
of the cutting guide)
Cutting Metal
 For cutting with bonded abrasives, always use the pro-
tection guard for cutting 14.
When cutting, work with moderate feed, adapted to the mate-
rial being cut. Do not exert pressure onto the cutting disc, tilt
or oscillate the machine.
Do not reduce the speed of running down cutting discs by ap-
plying sideward pressure.
When cutting profiles and square bar, it is best to start at the
smallest cross section.
Cutting Stone
 Provide for sufficient dust extraction when cutting
stone.
 Wear a dust respirator.
 The machine may be used only for dry cutting/grinding.
Thumbwheel Position
2 – 3
3
4 – 6
6
6
The machine must al-
ways work in an up-
grinding motion. Other-
wise, the danger exists
of it being pushed un-
controlled out of the
cut.
Bosch Power Tools