Werbung
Verfügbare Sprachen
Verfügbare Sprachen
32 | English
If required, clean all the parts to be fitted before installing
them.
– Swivel the retracting blade guard (11) backwards. Hold
the retracting blade guard in this position.
– Place the new saw blade onto the interior clamping flange
(45).
– Slowly push the retracting blade guard back down.
– Attach the clamping flange (43) and the SDS bolt (46).
Press the spindle lock (33) until it engages and tighten
the SDS bolt by turning it anticlockwise.
Operation
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Transport Safety Lock (see figure F)
The transport safety lock (36) makes it easier to handle the
power tool when transporting it to various working locations.
Unlocking the power tool (work position)
– Press the tool arm down slightly by the handle (9) to re-
lease the transport safety lock (36).
– Pull the transport safety lock (36) all the way out.
– Slowly guide the tool arm upwards.
Locking the power tool (transport position)
– Loosen the locking screw (32) if it is clamping the slide
device (1) in place. Pull the tool arm fully forward and
tighten the locking screw again to lock the slide device.
– Screw the adjusting screw (5) all the way upwards.
– To lock the saw table (17) in place, tighten the locking
knob (19).
– Swing the tool arm downwards by the handle (9) until you
can press the transport safety lock (36) completely in-
wards.
The tool arm is now securely locked and ready for transport-
ation.
Preparing for operation
Extending the saw table (see figure G)
The free end of long workpieces must have something
placed underneath it or be supported.
The saw table can be extended left and right using the saw
table extensions (14).
– Loosen the clamping screw (15).
– Pull out the saw table extension (14) to the required
length.
– Retighten the clamping screw (15) to fix the saw table ex-
tension.
Moving the fence (see figure H)
You have to move the adjustable fence (25) to saw bevel
angles.
1 609 92A 6ST | (09.07.2021)
– Loosen the locking screw (47).
– Pull the adjustable fence (25) all the way out.
– Re-tighten the locking screw (47).
After sawing the bevel angles, slide the adjustable fence
(25) back again (loosen the locking screw (47); slide the
fence (25) completely inward; retighten the locking screw).
Clamping the Workpiece (see figure I)
To ensure maximum safety while working, the workpiece
must always be firmly clamped.
Do not saw workpieces that are too small to clamp firmly.
– Press the workpiece firmly against the fences (25)
and (13).
– Insert the supplied screw clamp (26) into one of the cor-
responding holes (49).
– Adjust the threaded rod (48) of the screw clamp to the
workpiece height.
– Tighten the threaded rod (48) to fix the workpiece in
place.
Setting mitre and bevel angles
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Experience and suitable special tools are required for this.
A Bosch after-sales service point will handle this work
quickly and reliably.
Always tighten the locking knob (19) firmly before
u
sawing. Otherwise the saw blade can become wedged in
the workpiece.
Setting mitre angles (see figure J)
The mitre angle can be set between 47° (left side) and 47°
(right side).
– Loosen the locking knob (19) if it is tightened.
– Push the lever (20), turn the saw table (17) left or right
by the locking knob and set the required mitre angle using
the angle indicator (22).
– Retighten the locking knob (19).
For quick and precise setting of commonly used mitre
angles, detents (23) are provided on the saw table:
Left
0°
45°; 22.5°; 15°
– Loosen the locking knob (19) if it is tightened.
– Push the lever (20) and turn the saw table (17) left or
right to the required detent.
– Release the lever again. The lever must be felt to engage
in the detent.
– Retighten the locking knob (19).
Setting Bevel Angles (see figure K)
The bevel angle can be set between 0° and 45°.
– Pull the adjustable fence (25) all the way out.
– Loosen the clamping handle (31).
Right
15°; 22.5°; 45°
Bosch Power Tools
Werbung
