Herunterladen Diese Seite drucken

Bosch 3 601 M41 000 Originalbetriebsanleitung Seite 28

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
that do not match the mounting hardware of the saw will
run off-centre, causing loss of control.
Never remove cuttings, wood chips, etc. from the cut-
u
ting area while the power tool is running. Always guide
the tool arm back to the neutral position first and then
switch the power tool off.
Do not touch the saw blade after working before it has
u
cooled. The saw blade becomes very hot while working.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Never make warning signs on the machine unrecognis-
u
able.
The power tool is delivered with a laser warning sign
u
(see table: "Symbols and their meaning").
Do not direct the laser beam at persons or
animals and do not stare into the direct or
reflected laser beam yourself. You could
blind somebody, cause accidents or damage
your eyes.
If laser radiation hits your eye, you must close your
u
eyes and immediately turn your head away from the
beam.
Do not use any optical instruments such as binoculars
u
to view the radiation source. Doing so can damage your
eye.
Do not direct the laser beam at persons who are look-
u
ing through binoculars or similar instruments. Doing
so can damage their eye.
Do not make any modifications to the laser equip-
u
ment. The setting options described in these operating
instructions can be used safely.
Do not use the laser goggles (accessory) as protective
u
goggles. The laser goggles make the laser beam easier to
see; they do not protect you against laser radiation.
Do not use the laser goggles (accessory) as
u
sunglasses or while driving. The laser goggles do not
provide full UV protection and impair your ability to see
colours.
Bosch Power Tools
Warning! If operating or adjustment devices other
u
than those specified here are used or other proced-
ures are carried out, this can lead to dangerous expos-
ure to radiation.
Do not replace the integrated laser with a laser of an-
u
other type. A laser that is not compatible with this power
tool could pose a risk to persons.
Symbols
The following symbols may be important for the operation of
your power tool. Please take note of these symbols and their
meaning. Correctly interpreting the symbols will help you to
operate the power tool more effectively and safely.
Symbols and their meaning
IEC 60825-1:2014
LASER RADIATION
<0.39mW, 650 nm
LASER RADIATION
DO NOT EXPOSE USERS OF
DO NOT EXPOSE USERS OF TELE-
TELESCOPIC OPTICS
CLASS 1M LASER PRODUCT
SCOPIC OPTICS
CLASS 1M LASER PRODUCT
Keep hands away from the cutting area
while the power tool is running. Con-
tact with the saw blade can lead to injur-
ies.
Wear a dust mask.
Wear safety goggles.
Wear hearing protection. Exposure to
noise can cause hearing loss.
Danger area! Keep hands, fingers and
arms away from this area.
The adjustable fence must be pulled out-
wards when sawing bevel angles.
3 601 M41 000
Observe the dimensions of the saw
3 601 M41 040
blade. The hole diameter must match the
tool spindle without play. If it is neces-
sary to use reducers, ensure that the di-
mensions of the reducer are suitable for
the base blade thickness and the saw
3 601 M41 0B0
blade hole diameter, as well as the tool
spindle diameter. Wherever possible, use
the reducers provided with the saw
25,4
blade.
English | 27
1 609 92A 6ST | (09.07.2021)

Werbung

loading