Herunterladen Inhalt Inhalt Diese Seite drucken

Specifications; Maintenance And Inspection - Hitachi UC 9SD Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 6
English

SPECIFICATIONS

CHARGER
Model
Charging HITACHI BATTERY
Charging time
Charging voltage
Weight
CHARGING
Before using the power tool, charge the battery as follows.
1. Insert the battery into the charger.
Insert the battery into the battery charger as shown
in Figs. 1, 2, 3, 4, 5 and 6.
Make sure it contacts the bottom of the battery
charger.
2. Connect the charger power cord to the receptacle.
Connecting the power cord will turn on the charger
(the pilot lamp lights up).
CAUTION
If the pilot lamp does not light up, pull out the
power cord from the receptacle and check the
battery mounting condition.
About 1 hour is required to fully charge the battery at
a temperature of about 20°C. The pilot lamp goes off
to indicate that the battery is fully charged.
CAUTION
If the battery is heated due to direct sunlight, etc.,
just after operation, the charger pilot lamp may
not light up. At that time, cool the battery first,
then start charging.
3. Disconnect the charger power cord from the
receptacle.
4. Hold the charger tight and pull out the battery.

MAINTENANCE AND INSPECTION

1. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do
so could result in serious hazard.
2. Cleaning on the charger
When the charger is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, as they melt
plastics.
3. Store idle charger
When not in use, the charger should be stored in dry,
high or locked-up place–out of reach of children.
4. Service parts list
A : Item No.
B : Code No.
C : No. Used
D : Remarks
4
UC7SD
EB712S
(1.2 Ah, 6 cells)
FEB7S
(1.4 Ah, 6 cells)
Approx. 1 hour (at 20°C)
7.2 V
1.1 kg
CAUTION:
MODIFICATIONS:
NOTE
Due to HITACHI's continuing program of research and
development, the specifications herein are subject to
change without prior notice.
IMPORTANT
Correct connection of the plug
The wires of the mains lead are coloured in accordance
with the following code:
As the colours of the wires in the mains lead of this tool
may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire coloured blue must be connected to the terminal
marked with the letter N or coloured black.
The wire coloured brown must be connected to the
terminal marked with the letter L or coloured red.
Neither core must be connected to the earth terminal.
NOTE
This requirement is provided according to BRITISH
STANDARD 2769: 1984.
Therefore, the letter code and colour code may not be
applicable to other markets except United Kingdom.
UC9SD
FEB9S
(1.4 Ah, 8 cells)
EB914
(1.4 Ah, 8 cells)
9.6 V
1.2 kg
Repair, modification and inspection of Hitachi Power
Tools must be carried out by a Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
Blue:
– Neutral
Brown:
– Live
UC12SD
FEB12S
(1.4 Ah, 10 cells)
EB1214L
(1.4 Ah, 10 cells)
12 V
1.5 kg

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Uc 7sdUc 12sd

Inhaltsverzeichnis