Interrupting Operation; Ending Operation; Transport; Storage - Kärcher HD 9/20-4 S ST Classic Bedienungsanleitung

High-pressure gun
3
Suction hose
4
Gate
5
Admixture: 3=high, 2=medium, 1=low
2. Plug the desired gate into the suction hose.
3. Fill the detergent into the container.
4. Screw the container onto the foam nozzle.
5. Disconnect the spray lance from the high-pressure
gun.
6. Connect the cup foam lance to the high-pressure
gun and hand-tighten.
7. Start up the high-pressure cleaner.
Recommended cleaning method
1. Spray the detergent sparingly on the dry surface and
let it work for a while (do not let it dry).
2. Rinse off the loosened dirt with the high-pressure
jet.
After operating with detergent
The cup foam lance must be flushed after use to prevent
the formation of detergent deposits.
1. Unscrew the container.
2. Pour the remaining detergent back into the original
packaging.
3. Fill the container with clear water.
4. Screw the container onto the cup foam lance nozzle.
5. Operate the cup foam lance for approx. 1 minute to
flush the detergent residue.
6. Empty the container.

Interrupting operation

1. Release the trigger.
The device switches off.
2. Push the safety latch forwards.
The high-pressure gun is secured.
Continuing operation
1. Push the safety latch backwards.
The high-pressure gun is unlocked.
2. Actuate the trigger.
The device switches on.

Ending operation

1. Close the water inlet.
2. Actuate the trigger.
3. Set the trigger to "I/ON" and allow the device to run
for 5-10 seconds.
4. Release the trigger.
5. Set the power switch to "0/OFF".
6. Pull the mains plug out of the socket only when your
hands are dry.
7. Dismantle the water supply hose on the water con-
nection of the device.
8. Actuate the trigger until the device is completely de-
pressurised.
9. Push the safety latch forwards.
The high-pressure gun is secured.

Transport

CAUTION
Risk of injury or damage due to non-observance of
the weight!
When transporting and storing the device, there is a risk
of injury and damage due to its weight.
Take into account the weight of the device for transpor-
tation and storage, see chapter Technical data.
16
Note
At least one helper is required to lift or carry the device.
 Transporting the device:
a Lift up and carry the device by the device's frame.
b Place the device on a suitable means of transport
(e.g. platform truck) and secure it against slipping
and tipping.
c When transporting in vehicles, secure the device
against rolling away, slipping and tipping accord-
ing to the respectively applicable guidelines.
CAUTION
Risk of injury or damage due to non-observance of
the weight!
When transporting and storing the device, there is a risk
of injury and damage due to its weight.
Take into account the weight of the device for transpor-
tation and storage, see chapter Technical data.
ATTENTION
Risk of damage due to frost!
Water that is not completely drained can damage the
device and accessories during freezing.
Empty the water completely from the device and acces-
sories.
Protect the device and accessories from frost.
1. Finish operation, see chapter Ending operation.
2. Dismantle the high-pressure hose or the high-pres-
sure hose line at the high-pressure connection of
the device, see chapter Installing accessories.
3. Remove the high-pressure hose from the high-pres-
sure gun, see chapter Installing accessories.
4. Allow the water to drain completely from the high-
pressure hose and the high-pressure gun with spray
lance.
5. Pull the mains plug out of the socket only when your
hands are dry.
6. Store the device and accessories in a frost-protect-
ed interior space.
Flushing device with antifreeze
If frost-free storage is not possible:
1. Close the water inlet.
2. Dismantle the water supply hose on the water con-
nection of the device.
3. Let the water run out of the device.
4. Pump commonly available anti-freeze through the
device.
Note
Use commonly available, Glycol-based vehicle anti-
freeze. Observe the handling instructions of the anti-
freeze manufacturer.
5. Turn the power switch to the "I/ON" position.
6. Operate the trigger lever for max. 1 min until the an-
ti-freeze is expelled from the device.
7. Turn the power switch to the "0/OFF" position.
8. Dismantle the high-pressure hose or the high-pres-
sure hose line at the high-pressure connection of
the device, see chapter Installing accessories.
9. Remove the high-pressure hose from the high-pres-
sure gun, see chapter Installing accessories.
10. Allow the water to drain completely from the high-
pressure hose and the high-pressure gun with spray
lance.
English

Storage

Store device