Declaration Of Conformity; Battery Charging; Changing The Tool - Bosch GOP 10,8 V-LI Professional Originalbetriebsanleitung

OBJ_BUCH-630-008.book Page 16 Tuesday, March 31, 2015 6:05 PM
16 | English
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards:
EN 60745-1, EN 60745-2-4.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 18.02.2015
Assembly

Battery Charging

 Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
Removing the battery
To remove the battery 2, press the unlocking buttons 1 and
pull the battery out of the machine to the rear. Do not exert
any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
4 indicate the charge condition of the battery 2. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
To indicate the charge condition, press and hold button 3 of
the switched off machine.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
1 609 92A 116 | (31.3.15)

Changing the Tool

 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
 Wear protective gloves when changing application
tools/accessories. Contact with the application tool/ac-
cessory can lead to injuries.
Selecting the Application Tool/Accessory
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
Capacity
2/3
1/3
<1/3
Reserve
Accessory Material
HCS wood seg- Wooden materials,
ment saw blade* plastic
BIM segment saw Wooden materials,
blade* plastic, non-ferrous
metals
HCS plunge cut Wooden materials,
saw blades, plastic, gypsum
wood* and other soft
materials
BIM plunge cut Metal (e. g. unhard-
saw blades, ened nails, screws,
metal* smaller profiles),
non-ferrous metals
BIM plunge cut Wood, metal, non-
saw blade, wood ferrous metals
and metal*
HM-Riff segment Grouting joints,
saw blade* soft wall tiles,
glass-fibre reinforc-
es plastic and other
HM-Riff delta
abrasive materials
plate*
Scraper, rigid* Carpets, coverings
Scraper, flexible* Silicone and other
elastic materials
Base plate for Depends on sand-
sanding, series ing sheet
Delta 93 mm*
Bosch Power Tools