Behringer Neutron Bedienungsanleitung Seite 14

14
NEUTRON User Manual
5.13 VCF mod Source
Long Press VCF Mode then the LFO shape LED wheel will indicate the current mod
source selection:
Not used
Disabled
Note-On velocity
Mod-wheel (CC1)
Aftertouch
Press RANGE +/- to select the output.
Press VCF MODE to toggle between setting the mod source & depth.
This gives you the power to play the filter via velocity changes or use Aftertouch
to open up the filter after a note is played.
5.14 VCF mod Depth
Long Hold filter (VCF) MODE, Press VCF MODE to toggle between setting the
mod source & depth. When in VCF mod depth mod the LFO shape LED wheel will
indicate the current VCF mod depth: 1%−100% (64 steps)
Press RANGE +/- to select the output of depth. Adjusting the VCF Mod depth
allows a sound to have a more restricted filter sweep which may be used to
create interesting effects.
5.15 Poly-Chaining
If you have multiple Neutron units, you can connect them in a 'Poly Chain' to
produce polyphonic sounds. The Neutron works by sending unhandled notes
to the next in the chain. When the chain runs out, the notes are dropped
(i.e. not played). The first Neutron plays the first played note, the second plays
the second, the third plays the third etc. Note that a Neutron in Paraphonic mode
will handle 2 notes. Each Neutron must have the same MIDI channel number
set using the rear panel switches. The Poly Chain connections are shown in the
diagram. Set the Poly Chain ON for all Neutrons. The last Neutron in the chain can
either be set to Poly Chain on or off depending on how you would like the MIDI
information to be handled. If Poly Chain is on, the last Neutron will act as if it is
sending the next played note over the maximum number of notes played to the
next device in the chain, and the note will not be heard or dropped. If Poly chain
is off for the last Neutron, the next played note over the maximum number of
notes will steal the last played note from the last Neutron.
To toggle Poly Chain mode, press and hold the PARAPHONIC button for 2 seconds.
The LED will repeatedly flash (once when in mono mode - twice when in duo
mode). A short press on the PARAPHONIC button will still toggle the PARA/DUO
mode. Hold PARAPHONIC to exit. If you are only using one Neutron, make sure the
Poly Chain is OFF.
5.16 Note Priority
Note priority can be set by long pressing the OSC SYNC button. The VCF mode
LEDs will now indicate the note priority. Note priority allows different playing
styles and effects to be used creatively.
HPF = high note priority
BPF = last note priority (default)
LPF = low note priority
5.17 Pedal mode
Press & hold OSC2, then pressing KEYTRK will toggle the state of of the mode.
When the KEYTRK LED is lit - OSC 2 will play the last note played before Pedal
Mode was enabled with each new note played. This starts when any
key is pressed.
When KEYTRK LED is not lit - OSC2 will behave normally.
5.18 Features via Sysex and Neutron app only
Autoglide
Autoglide sets the number of semitones that the start of the note 'glides through'
for the selected note. This can be a + value (so the note glides down), or a - value
(so the note glides up). It is played as a smooth and linear increase or decrease
in pitch rather than a semitone step-change. The speed of the glide is set by the
Porta control.
When activated the Neutron will now glide up/down +/-12 semitones. If notes
overlap (played legato) this will allow easy programming of 303 style patterns
using a typical piano roll editor in a DAW.
Set pitch bend range
Select the pitch bend range from 0 to +/-24 semitones (two octaves).
Key split
Create a key split at the desired note. Notes played below the split point will
trigger oscillator 1 and notes above will trigger oscillator 2.
LFO shape order
Populate the 5 LFO locations with any of the 5 available wave shapes. The order
will directly match the order of the LFO control on the unit going clockwise.
LFO phase
Select the start position of the waveform each time the LFO is triggered. This can
be set for each of the 5 LFO positions independently. This can be used to create
unusual modulations and textures.
Setting midi channel (auto disable dip switches)
Set the MIDI channel without the need to access the MIDI DIP switches on the
back of the unit. Setting the channel this way automatically disables the DIP
switches. This function is useful when using the Neutron in a separate Eurorack
set up rather than its factory supplied case.