Inhaltsverzeichnis
Werbung
VOCODER VC340 Getting started
(EN) Step 3: Getting
started
OVERVIEW
This "getting started" guide will help you set up
the VOCODER VC340 analog synthesizer and briefly
introduce its capabilities.
CONNECTION
To connect the VOCODER VC340 to your system,
please consult the hook-up guide earlier in this
document
SOFTWARE SETUP
The VOCODER VC340 is a USB Class Compliant MIDI
device, and so no driver installation is required, and
it does not require any additional drivers to work
with Windows and MacOS.
HARDWARE SETUP
1.
Make all the connections in your system.
2.
Apply power to the VOCODER VC340 using the
supplied IEC power cord only.
3.
Make sure the main volume knob is turned
down and that your amplifiers or powered
speakers are turned off.
4.
Turn on the rear panel power switch, and
then turn on the rest of your system.
UPPER/LOWER
The keyboard split has two positions marked
HIGH and LOW on the top panel, and this depends
upon the setting of the HIGH/LOW octave switch.
Any UPPER switches ON will allow the keys above the
split to play. Any LOWER switches ON will allow the
keys below to play.
INITIAL SETUP (STRINGS)
The following example using STRINGS, will get you
started:
1.
Turn on the UPPER and LOWER STRINGS
switches.
2.
Turn up the STRINGS fader in the BALANCE
section.
3.
Play the keyboard and adjust the VOLUME
and the settings of your external equipment
to a safe listening level.
4.
Adjust the ATTACK fader to vary the amount
of time taken for the maximum level to be
reached after a key press.
5.
Adjust the RELEASE fader to vary the amount
of time taken for the sound level to decay
once a key is released. This fader also affects
the HUMAN VOICE and VOCODER.
6.
Adjust the TONE fader.
ADDING HUMAN VOICE
7.
Turn on some of the HUMAN VOICE switches.
8.
Adjust the HUMAN VOICE fader in the
BALANCE section as you play. Readjust the
STRINGS fader to balance or turn it down/off
as desired.
9.
Experiment with the other switches such
as ENSEMBLE.
10.
Adjust the HUMAN VOICE ATTACK fader
as desired.
11.
Adjust the RELEASE fader as mentioned in the
STRINGS section above.
12.
Adjust the three VIBRATO faders to add
modulation to the HUMAN VOICE if desired.
These faders also affect the VOCODER.
ADDING DIRECT MICROPHONE
13.
Turn on your microphone and sing along
or talk. This is the direct vocals, with no
added VOCODER.
14.
Adjust the MIC LEVEL fader in the VOCODER
section, making sure that the level is not high
enough for the adjacent red LED to come on.
15.
Adjust the DIRECT MIC fader in the BALANCE
section, and adjust the STRINGS and HUMAN
VOICE fader as desired.
USING THE VOCODER
16.
Turn on the UPPER and LOWER VOCODER
switches.
17.
Turn on your microphone and sing along
or talk.
18.
Turn down the DIRECT MIC fader, and the
STRINGS and HUMAN VOICE faders.
19.
Adjust the MIC LEVEL fader in the VOCODER
section, making sure that the level is not high
enough for the adjacent red LED to come on.
20.
As you play the keyboard and sing/talk, you
will hear the VOCODER output. (There will
be no output if you are not singing or talking
while playing, or if the MIC LEVEL is down.
21.
Try using the ENSEMBLE.
22.
Adjust the VOCODER TONE fader, and
re-adjust the MIC LEVEL as desired, to prevent
feedback from your speakers.
23.
Adjust the three VIBRATO faders to add
modulation to the VOCODER if desired. These
faders also affect the HUMAN VOICE.
24.
Add in the STRINGS and HUMAN VOICE by
adjusting their faders in the BALANCE section.
Werbung
Inhaltsverzeichnis
