Care; Troubleshooting; Installation; Safety - STIEBEL ELTRON FEK 2 Bedienung Und Installation

INSTALLATION

Care

Menu Function of the Touch-Wheel
SETTINgS go to the SETTINgS menu.
Menu item Description
INFO
PROgRAM- Software version installed on the ap-
 
MINg uNIT pliance.
SOFTWARE
HEATINg Heating circuit for which the appli-
 
CIRCuIT ance is installed.
HEATINg PRO- Set the times during which heating to
gRAM the comfort temperature should take
place. In the intervals in between,
heating takes place to the ECO tem-
perature.
You can adjust the set temperature
values on the appliance in menu item
SETTINgS / HEATINg / COMFORT TEM-
PERATuRE and ECO TEMPERATuRE.
If you adjust the set temperatures on
the appliance, you will no longer be
able to adjust the menu items via the
heat pump manager.
Certain menu items are protected by
SETTINgS
a code. The factory-set code is 1 0 0 0.
Ask your qualified contractor to set
these menu items for you.
VIEW Entering the code will unlock the
 
code-protected parameters for a cer-
tain length of time.
gENERAL
 
  LAN- Set the required system language.
guAgE
CON- Set the required contrast level for the
 
TRAST display.
BRIgHT- Set the brightness of the display for
 
NESS when you are operating the appli-
ance.
BRIgHT- Set the brightness of the display for
 
NESS OFF when you are not operating the ap-
pliance.
ROOM Set this parameter if the temperature
 
TEMPERA- sensor of the appliance is not meas-
TuRE COR- uring the room temperature correctly
RECTION due to the installation location.
RELATIVE Set this parameter if the humidity sen-
 
HuMIdITY sor of the appliance is not measuring
CORREC- the relative humidity correctly due to
TION the installation location.
TOuCH Set the touch sensitivity of the Touch-
 
SENSITIVITY Wheel and sensor buttons.
dELETE delete the minimum and maximum
 
MIN/MAX values (INFO menu).
FACTORY Reset the appliance to its delivered
 
SETTINg condition.
  HEATINg
COMFORT Adjust the set room temperature.
 
TEMPERA-
TuRE
ECO TEM- Adjust the set room temperature.
 
PERATuRE
FEK 2
Menu Function of the Touch-Wheel
  ROOM IN- 0 = The room sensor captures the
FLuENCE room temperature only.
>0 = The room sensor also regulates
the room temperature. The higher the
value, the more influence the room
sensor has. When the set temperature
is reached, the heating circuit pump
switches off.
HEATINg Your qualified contractor will have
 
CuRVE RISE set up a building- and system-spe-
cific heating curve for every heating
circuit. For heating circuit 1 the curve
relates to the heat pump return tem-
perature; for heating circuit 2 to the
mixer flow temperature.
Adjust the heating curve as required.
HEATINg display the currently set heating
 
CuRVE VIEW curve.
6. Care
A damp cloth is all you need to clean the plastic parts. Never
use abrasive or corrosive cleaning agents.
7.

Troubleshooting

If you cannot remedy the fault, contact your qualified contrac-
tor. To facilitate and speed up your enquiry, please provide
the serial number from the type plate (000000-0000-000000).
INSTALLATION

8. Safety

Only a qualified contractor should carry out installation, com-
missioning, maintenance and repair of the appliance.
8.1

General safety instructions

We guarantee trouble-free function and operational reliability
only if original accessories and spare parts intended for the
appliance are used.

8.2 Instructions, standards and regulations

Note
Observe all applicable national and regional regula-
tions and instructions.

9. Appliance description

The appliance is a remote control unit for the connected heat
pump manager. This appliance can operate one heating circuit.
The heat pump manager uses the measured room tempera-
ture and the selected set temperature to regulate the heating
temperature.
| 13