Makita BTD200 Betriebsanleitung Seite 3

ENGLISH
1 Battery cartridge
2 Button
3 Terminal cover
4 Charging lights
5 Battery charger
6 Bit
SPECIFICATIONS
Model
Capacities
Wood screw ................................................. 6 mm
Self drilling screw .......................................... 6 mm
Hex screw ..................................................... 6 mm
-1
No load speed (min ) .................... High: 0 – 2,000
Impacts per minute .......................... High: 0 – 3,000
Overall length ............................................... 232 mm
Net weight ....................................................... 2.9 kg
Rated voltage ............................................ D.C. 24 V
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY
CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
Explanation of general view
7 Sleeve
8 Switch trigger
9 Reversing switch lever
10 A side
11 B side
12 Clockwise
9. Do not operate charger if it has received a
BTD200
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
10. Do not disassemble charger or battery car-
tridge; take it to a qualified serviceman when
service or repair is required. Incorrect reas-
Low: 0 – 1,600
sembly may result in a risk of electric shock or
fire.
Low: 0 – 2,500
11. To reduce risk of electric shock, unplug
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
12. The battery charger is not intended for use by
young children or infirm persons without
supervision.
13. Young children should be supervised to
ensure that they do not play with the battery
charger.
14. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
15. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1. Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
2. Do not attempt to use a step-up transformer,
an engine generator or DC power receptacle.
3. Do not allow anything to cover or clog the
charger vents.
4. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
(2) Avoid storing battery cartridge in a con-
(3) Do not expose battery cartridge to water or
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
5. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
13 Counterclockwise
14 Speed change lever
15 Limit mark
16 Brush holder cap
17 Screwdriver
ductive material.
tainer with other metal objects such as
nails, coins, etc.
rain.
3