Specifications; Specific Safety Rules - Makita 6918D Betriebsanleitung

ENGLISH
1 Push button
2 Battery cartridge
3 Socket
4 Pin
5 O-ring
6 Switch trigger

SPECIFICATIONS

Model
Capacities
Standard bolt ................................................ M8 – M14
High tensile bolt ............................................ M6 – M12
Square drive ...................................................... 12.7 mm
–1
No load speed (min ) ...................................... 0 – 2,300
Impacts per minute ........................................... 0 – 3,000
Max. fastening torque ........................................ 120 N•m
Overall length ..................................................... 176 mm
Net weight (with battery cartridge) ........................ 1.6 kg
Rated voltage ................................................... D.C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note:Specifications may differ from country to country.
Intended use
The tool is intended for fastening bolts and nuts.
Safety Hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may result
in a risk of overheating, possible burns and even
an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
4
Explanation of general view
7 Reversing switch lever
8 A side
9 B side
10 Clockwise
11 Counterclockwise
12 Fastening time
7.
6918D
8.
9.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
2.
3.
4.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
ENC004-1
(gained from repeated use) replace strict adherence
to impact wrench safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1.
2.
3.
4.
5.
6.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
13 Seconds
14 Proper fastening torque for
15 Fastening torque
16 Limit mark
17 Screwdriver
18 Brush holder cap
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal parts
of the tool "live" and shock the operator.
Wear ear protectors.
Check the socket carefully for wear, cracks or
damage before installation.
Hold the tool firmly.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
The proper fastening torque may differ depend-
ing upon the kind or size of the bolt. Check the
torque with a torque wrench.
GEB009-2