Maintenance - Kress KG155E Bedienungsanleitung

Only one light is
flashing three times
per cycle.
Only one light is
flashing four times
per cycle.
OPERATION:
To start(See Fig. F)
Warning! The cutting head continues to rotate
after the trimmer has been switched off; wait
until it has completely stopped then lay down the
tool.Press the lock-off button first, then press the
switch trigger to start the machine.
ECO Speed (See Fig.G)
For longer run time, press the ECO button and
switch trigger, then your machine will operate at a
low speed.
Trimming(See Fig.H)
Bump feed(See Fig.I)
Assembling and removing the trimmer head
(See Fig. J)
Insert the hex key into the hole and rotate the
trimmer head until it stops in a locked position. Then,
18
rotate counterclockwise to remove it, and clockwise
to assemble it.
EN
Winding the trimmer line(See Fig. K)
NOTE: The spool must be wound while inside the
trimmer head. The spool cannot be wound with line,
then installed into the trimmer head.
Assembling the brush cutter blade(See Fig.
L1, L2, L3)
Remove the trimmer head and the skirt before
assembling the brush cutter blade.
Insert the hex key into the hole. Place the brush-
cutter blade on top of the spacer, place washer on
top of the brush-cutter blade, place blade housing
over washer. After that, use the wrench to tighten the
lock-nut.
Cutting(See Fig. M)
ATTACHMENT-CAPABLE ACCESSORIES
The below attachment accessories are sold
separately to convert the grass trimmer into a tool for
various applications.
1. Hedge trimmer attachment (KA0420)
This attachment is intended for cutting and
trimming hedges and bushes in domestic use.
2. Pruning saw attachment (KA2642)
This attachment is intended for sawing of trees,
tree trunks, branches, limbs, etc. Cuts can be
sawed with or across the grain. This product is
not suitable for sawing mineral materials.
At least one battery is hot,
wait for them cool down
before start again.
The machine is over load.
Raise the cutting height or
push slowly.
3. Edger attachment (KA2283)
This attachment is intended for edging around
walkways, driveways, flower beds, etc.
OPERATION
INSTRUCTIONS
WARNING! The charger and battery pack
are specially designed to work together so
do not attempt to use any other devices. Never
insert or allow metallic objects into your charger or
battery pack connections because of an electrical
failure and hazard will occur.
1. Bump-line feed system (See Fig. I)
The trimmer is equipped with a bump-line system.
Just bump the trimmer head while the machine is
running, new line will feed out.
2. Winding the trimmer line (See Fig. K)
Insert the replacement line through the eyelet and feed it
through the other side. Ensure both ends of the line are
even on each end of the trimmer head (recommended
2m) and cut the line. Turn the dial clockwise to wind the
line around the spool until about 19cm remains on either
side.
STORING YOUR GRASS
TRIMMER
Always remove the battery pack from your
trimmer after use.
To store your grass trimmer
The trimmer is provided with a hanging slot for
storing the trimmer on the wall. (See Fig. N)
Store in a dry place where the trimmer and battery
can be protected from damage.

MAINTENANCE

Always remove the battery pack from your
trimmer after use.
Always check the product prior to being used for
any damage.
After use, disconnect the battery from the tool and
check for damage.
Your power tool requires no additional lubrication or
maintenance. There are no user serviceable parts
in your power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool in
a dry room temperature location. Keep the motor
ventilation slots clean. Keep all working controls
free of dust.
FOR BATTERY TOOLS
The ambient temperature range for the use and