Technical Data - Cloer 451 Serie Bedienungsanleitung

Technical Data

type volt
451/452 220-240
Before initial use
Read these operating instructions
carefully before using the
appliance for the first time
• Remove all packaging elements and labels, but not
the rating plate.
• Place the electric kettle on a dry, even, non-slip sur-
face.
• Shake out the water from the first boiling process.
Safety notices for use of the
contact base / electric kettle
The appliance meets the
requirements of the
applicable EC directives.
The appliance is intended
for in door use only.
CAUTION! The surface is hot
during operation. Only touch
the device at its handle.
Never operate the electric kettle without
the lid closed and without lime filter,
since then the device will not shut off
automatically when the water boils.
ATTENTION! Always unplug appliance
when not in use and before cleaning!
• Do not fill the electric kettle with water past the MAX
marking. Scalding may result from water boiling over.
• Note: Make sure that the kettle is filled with water at
least up to the MIN mark (0.5l) and at most up to the
MAX mark (451X = 1l / 452X = 1.7l) on the water level
indicator.
• Always remove the electric kettle from the
contact base before filling with water.
• This electric kettle may only be used for heating water.
• Before operating the machine, make sure that the
contact base is dry.
• Please make sure that water is never spilled on the
contact base.
• If water is accidentally spilled onto the contact base,
proceed as follows:
– Unplug the unit from the wall socket.
– Dry the contact base with an absorbent dry kitchen
towel.
– Dry the surface beneath the contact base.
– Plug the unit into the wall socket again.
hz watt
50 1850-2200
• Plug the power plug into the wall socket.
• Remove the electric kettle from the contact base.
• NOTE: For your safety, the lid is equipped with a lo-
• Fill the electric kettle with water.
• Close the lid manually.
• MAKE SURE not to fill water past the maximum mar-
• Place the electric kettle anywhere on the contact
• To switch it on, press the ON/OFF switch on the bot-
• When the water boils, the electric kettle automatical-
• You can interrupt the boiling process at any time by
• To pour the water, lift the electric kettle from the con-
• IMPORTANT: Always make sure that the device is
• The appliance must not be immersed in water! Do
• Clean very dirty appliances either with lukewarm wa-
• If a stainless steel cleaner is used, make sure that it is
NOTE
Never operate the electric kettle without the lid
closed and without lime filter, since then
the device will not shut off automatically
when the water boils.
Operation
Open the lid of the removable kettle by pressing the
button to open the lid.
cking device. If the electric kettle is accidentally over-
turned during use, the lid will not open. This reduces
the risk of being scalded by spilled water.
king on the water level indicator.
base. The unit is now ready for operation.
tom of the handle. The switch locks into place and the
control lamp lights up.
ly switches off and the control lamp goes out.
pushing up the ON/OFF switch.
tact base.
switched off before removing the electric kettle from
the contact base.
NOTE
The electric kettle has a silicone cover over the spout,
which serves as protection from dust and splashes.
This cover must not be removed and does not hinder
the liquid from being poured out.
Overheating protection device
The electric kettle is equipped with a doubleaction
overheating protection device. In the event that you
accidentally operate the electric kettle without water
or if the water level is too low, causing the water to
evaporate during boiling, the device will automati-
cally switch off for your safety. The device will be rea-
dy to operate once it has been filled with cold water.
Cleaning
not clean the electric kettle with heavily abrasive
cleaners. They could scratch the appliance.
ter or with a stainless steel cleaner.
not aggressive and does not contain chlorine or acids.
EN
7