janitza 96-PA-RCM Installationsanleitung Seite 6

Rcm-module

Vorschau ausblenden Andere Handbücher für 96-PA-RCM:

Installationsanleitung (10 Seiten)

Benutzerhandbuch und technische daten (48 Seiten)

Handbuch (54 Seiten)

Seite von 10

/ 10
Lesezeichen

Verfügbare Sprachen

RCM modules

Expansion modules for the device series

UMG 96-PA

Installation instructions

Fig.

UMG 96-PA with module 96-PA-RCM-EL (with Ethernet interface)

Janitza electronics GmbH

Vor dem Polstück 6

35633 Lahnau | Germany

Support tel. +49 6441 9642-22

info@janitza.de | www.janitza.de

Safety

2 2

Brief device description

Safety information

The installation instructions do not represent a

The RCM module enhances the scope of func-

compete set of all safety measures required for

tions of the basic device and is available in the

the operation of the device.

following variants:

Special operating conditions can require addi-

• Module 96-PA-RCM-EL

tional measures. The installation manual contains

with Ethernet interface

information which must be observed to ensure

• Module 96-PA-RCM

your personal safety and avoid material damage.

without Ethernet interface

Symbols used on the device:

Functions of the two module variants:

• Neutral conductor measurement (I4).

The additional symbol on the de-

• Residual current measurement (RCM) or DC

vice itself indicates an electrical

measurement (2 analog inputs).

danger that can result in serious

• Temperature measurement (1 analog input).

injuries or death.

This general warning symbol

Both module variants are suitable for the moni-

draws attention to a possible risk

toring of:

of injury. Be certain to observe all

• Residual currents (RCM) - Type A, B and B+.

of the information listed under this

• AC currents.

symbol in order to avoid possible

• DC currents and pulsating DC currents.

injury or even death.

The basic device with module measures residual

currents according to IEC/TR 60755 of:

Type A

Type B and B+ (extended frequency range)

RCM modules

• Module 96-PA-RCM

• Module 96-PA-RCM-EL

Expansion modules for the device series

UMG 96-PA

and UMG 96-PQ-L

(from ﬁ rmware 2.0)

Installation instructions

Fig.

UMG 96-PA with module 96-PA-RCM-EL (with Ethernet interface)

Safety information in the installation instructions

is marked by a warning triangle and, in depen-

dence on the degree of hazard, is displayed as

follows:

DANGER

Warns of an imminent danger which results in seri-

ous or fatal injury.

WARNING

Warns of a potentially hazardous situation which

could result in serious injury or death.

CAUTION

Warns of a potentially hazardous situation which

could result in minor injury or material damage.

ATTENTION

Warns of an imminently hazardous situation that

can result in material or environmental damage.

INFORMATION

Indicates procedures in which there is no hazard

of personal injury or material damage.

General

Disclaimer

Compliance with the usage information for the

devices is a prerequisite for safe operation and

attaining the stated performance characteristics

and product features. Janitza electronics GmbH

assumes no liability for bodily injury, material

damage or ﬁ nancial losses which result from

disregard of the usage information. Make sure

that your usage information is readily available

and legible.

Further usage information, such as user manuals

for the basic devices and modules, can be found

on our website at

www.janitza.de under Support > Downloads.

User Manual:

distribution or other use, in whole or in part, is

prohibited.

Subject to technical alterations.

• Make sure that your device matches the instal-

• First make sure you have read and understood

Mounting

Safety measures

When operating electric devices, it is unavoidable

for certain parts of these devices to conduct

hazardous voltage. Consequently, severe bodily

injury or material damage can occur if they are

DANGER

not handled properly:

• Before making connections to the device,

ground the device by means of the ground

wire connection, if present.

• Hazardous voltages can be present in all

WARNING

circuitry parts that are connected to the power

Fig. basic device

supply.

• There can still be hazardous voltages present

Fig.Module 96-PA-RCM-EL

(with Ethernet interface)

in the device even after it has been discon-

CAUTION

nected from the supply voltage (capacitor

storage).

• Do not operate equipment with current trans-

Disregard of the installation instructions may

former circuits when open.

cause property damage or personal injury!

• Do not exceed the limit values speciﬁ ed in the

Disregard of the installation instructions may cause

user manual and on the rating plate! This must

damage to your basic device with module or de-

stroy it and/or may also result in personal injury.

also be observed during testing and commis-

· Observe the assembly instructions of your

sioning!

basic device.

• Be certain to observe the information con-

· Disconnect your basic device from the power

tained in the user manual to protect your IT

supply prior mounting the module!

· Provide adequate air circulation in your instal-

system, network, data communication and

lation environment and cooling, as needed,

measurement devices!

when the ambient temperatures are high.

• Take note of the safety and warning notices

· Before mounting, remove the transport pro-

tection from the module connector plug of the

in the documents that belong to the device!

module and the protection from the module

connector socket of the basic device.

6 / 10

General

Disclaimer

Compliance with the usage information for the

devices is a prerequisite for safe operation and

attaining the stated performance characteristics

and product features. Janitza electronics GmbH

assumes no liability for bodily injury, material

damage or ﬁ nancial losses which result from

disregard of the usage information. Make sure

that your usage information is readily available

and legible.

Further usage information, such as user manuals

for the basic devices and modules, can be found

on our website at

www.janitza.de under Support > Downloads.

distribution or other use, in whole or in part, is

prohibited.

Subject to technical alterations.

• Make sure that your device matches the instal-

lation instructions.

• First make sure you have read and understood

the usage information accompanying the

product.

Mounting

Safety measures

When operating electric devices, it is unavoidable

for certain parts of these devices to conduct

Module connector

socket

hazardous voltage. Consequently, severe bodily

injury or material damage can occur if they are

not handled properly:

• Before making connections to the device,

ground the device by means of the ground

Mounting module:

wire connection, if present.

1. Disconnect the system (basic device) from the power

• Hazardous voltages can be present in all

circuitry parts that are connected to the power

2. Remove the transport protection from the module

Fig. basic device

supply.

• There can still be hazardous voltages present

3. Slide the module into the slot on the rear side of

in the device even after it has been discon-

nected from the supply voltage (capacitor

storage).

CAUTION

• Do not operate equipment with current trans-

4. Connect the system (basic device) to the power

Disregard of the installation instructions may

former circuits when open.

cause property damage or personal injury!

• Do not exceed the limit values speciﬁ ed in the

Disregard of the installation instructions may cause

user manual and on the rating plate! This must

damage to your basic device with module or de-

stroy it and/or may also result in personal injury.

also be observed during testing and commis-

· Observe the assembly instructions of your

sioning!

basic device.

If the module is not detected during the startup proce-

• Be certain to observe the information con-

· Disconnect your basic device from the power

dure:

tained in the user manual to protect your IT

supply prior mounting the module!

· Disconnect your system (the basic device) from

· Provide adequate air circulation in your instal-

system, network, data communication and

lation environment and cooling, as needed,

measurement devices!

when the ambient temperatures are high.

• Take note of the safety and warning notices

· Before mounting, remove the transport pro-

· If necessary, restart the basic device.

tection from the module connector plug of the

in the documents that belong to the device!

· If these measures are unsuccessful, please contact

module and the protection from the module

connector socket of the basic device.

• Keep the usage information associated with

the product available for the entire service life

and pass it on to any possible subsequent

users.

• Please ﬁ nd out about device revisions and

the associated modiﬁ cations of the usage

information associated with your product at

www.janitza.de.

Disposal

Please abide by national regulations! Dispose

of individual parts, as applicable, depending on

their composition and existing country-speciﬁ c

regulations, e.g. as:

• Electronic waste

• Plastics

• Metals

or engage a certiﬁ ed disposal

company to handle scrapping.

Relevant laws,

standards and directive used

Please see the declaration of conformity on our

website (www.janitza.de) for the laws, standards

and directives applied for the device by Janitza

electronics GmbH.

Module-connector plug

Qualiﬁ ed personnel

To avoid bodily injury and material damage,

only qualiﬁ ed personnel with electrical training

are permitted to work on the device who have

knowledge of:

• the national accident prevention regulations,

Fig.Module 96-PA-RCM-EL

• safety technology standards,

(with Ethernet interface)

• installation, commissioning and operation of

Mounting module:

the device.

1. Disconnect the system (basic device) from the power

supply!

2. Remove the transport protection from the module

WARNING

connector plug of the module and the protection from

Risk of injury due to electrical voltage!

the module connector socket of the basic device.

Severe bodily injury or death can result from:

3. Slide the module into the slot on the rear side of

· Touching bare or stripped leads that are ener-

the basic device and use slight pressure to press

gized.

it into the basic device until the module connector

· Device inputs that pose a hazard when

audibly snaps in.

touched.

4. Connect the system (basic device) to the power

Before starting work on your system:

· Disconnect the supply of power to the

supply. The basic device recognizes the plugged

· Disconnect the supply of power to the

system!

in module automatically.

· Secure it against being switched on!

· Check to be sure it is de-energized!

INFORMATION

· Ground and short circuit!

· Cover or block off adjacent live parts!

If the module is not detected during the startup proce-

dure:

· Disconnect your system (the basic device) from

the power supply and check the positioning of the

RCM module. Carefully press the module onto the

basic device until it audibly snaps into place.

· If necessary, restart the basic device.

· If these measures are unsuccessful, please contact

our support team (www.janitza.de)!

Inhaltsverzeichnis

Diese Anleitung auch für:

96-pa-rcm-el

janitza 96-PA-RCM Installationsanleitung Seite 6

Verfügbare Sprachen

Verwandte Anleitungen für janitza 96-PA-RCM

Verwandte Produkte für janitza 96-PA-RCM

Diese Anleitung auch für: