Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
3.2 Parameter Settings
LED Display
Definition
Motor Type
F1
Dual or Single Gate
F2
Over-Current Setting
F3
Operation Speed
F4
Acceleration/Deceleration
F5
function (soft start/stop)
Acceleration/
F6
Deceleration Speed
(soft start/stop speed)
F7
Open/Close delay of
dual gate operation
F8
Auto-Close adjustment
F9
Photocell function
mode when using
2 photocells
FA
Pedestrian Mode function
(45° opening angle)
FB
Pre-Flashing function
Parameter
Table
F1-1
Motor only
F1-2
Motor with Limit Switch
F1-3
Motor with Hall sensor
F2-1
Dual Gate
F2-2
Single Gate
01
0.1A
11
02
0.2A
12
03
0.3A
13
04
0.4A
14
05
0.5A
15
06
0.6A
16
07
0.7A
17
08
0.8A
18
09
0.9A
19
10
1A
20
1. Factory setting "F3-25".
F4-1
100% Full speed
F4-2
90% Full speed
F4-3
80% Full speed
F4-4
70% Full speed
F4-5
60% Full speed
F5-1
Function ON
F5-2
Function OFF
F6-1
70% Full speed
F6-2
50% Full speed
F6-3
30% Full speed
00
0 sec
11
2 sec
01
12
3 sec
02
13
4 sec
03
14
5 sec
04
15
6 sec
05
16
7 sec
06
17
8 sec
07
18
9 sec
08
19
10 sec
09
20
10
12 sec
F8-0
Function OFF
F8-1
3 sec
F8-2
10 sec
F8-3
20 sec
F8-4
40 sec
F8-5
60 sec
F8-6
120 sec
F8-7
180 sec
F8-8
300 sec
F9-1
Mode 1
F9-2
Mode 2
F9-3
Mode 3
F9-4
Mode 4
FA-0
Function OFF
Function ON
FA-1
FB-0
Function OFF
FB-1
Function ON
29
Description
1. The factory setting is "F1-3".
1. The factory setting is "F2-1".
1.1A
21
2.1A
1.2A
22
2.2A
1.3A
23
2.3A
1.4A
24
2.4A
1.5A
25
2.5A
1.6A
26
2.6A
1.7A
27
2.7A
1.8A
28
2.8A
1.9A
29
2.9A
2.0A
30
3.0A
1. The factory setting is "F4-3".
1. The factory setting is "F5-1".
1. The factory setting is "F6-3".
14 sec
1. The factory setting is "F7-01".
16 sec
18 sec
20 sec
22 sec
24 sec
26 sec
28 sec
30 sec
35 sec
1.Only possible with photocell connected!!
2.Auto-close mode activates when the gates move to
the end position or stopped manually. If the
transmitter, push button, or the key-switch is
activated before the auto-close counting, the gate
will close immediately.
3.The factory setting is "F8-0".
1. Please see 3.3 photocell adjustment for more
information
2. The factory setting is "F9-1". For operation with a
photocell in standard function.
1. When function is on and button 2 on the remote
is pressed, one gate will open partially.
2. The factory setting is "FA-1".
1. When function is ON, the light will flash 3
seconds before the gate operates. If OFF, the
light will begin flashing when the motor begins.
2. The factory setting is "FB-0".
31
3.1A
41
4.1A
32
3.2A
42
4.2A
33
3.3A
43
4.3A
34
3.4A
44
4.4A
35
3.5A
45
4.5A
36
37
38
39
40
Werbung
Inhaltsverzeichnis
