Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL GP-CLM 47 S HW Li Originalbetriebsanleitung

Use special caution when backing up and pulling
the lawn mower. Tripping hazard!
Tips for proper mowing
It is recommended that you overlap the mo-
wing swaths.
Only use a sharp blade that is in good condition.
This will prevent the grass blades from fraying
and the lawn from turning yellow.
Try to mow in straight lines for a nice, clean look.
The swaths should overlap each other by a few
centimeters in order to avoid stripes.
How frequently you should mow your lawn is
determined primarily by the speed at which the
grass grows. In the main growing season (May
- June) you will probably need to mow the lawn
twice a week, otherwise just once a week. The
cutting height should be between 4 - 6 cm and the
amount of growth before mowing again should
be 4 - 5 cm. Normal grass which has grown to a
height of up to 8cm can be mown to the desired
height in one go without any problems. If the
grass is allowed to grow somewhat longer for
whatever reason, do not make the mistake of
cutting it back to the normal height in one go. This
will harm the lawn. For grass which has grown to
over 10 cm in height we therefore recommend
that you mow it with the highest cutting height
setting fi rst.
Important!
The cutting height setting has an infl uence on the
maximum area that can be mown.
Keep the underside of the mower housing clean
and remove grass build-up. Deposits not only
make it more diffi cult to start the mower; they
decrease the quality of the cut and make it harder
for the equipment to bag the grass.
Always mow along inclines (not up and down).
You can prevent the lawn mower from slipping
down by holding a position at an angle upwards.
Select the cutting height according to the length
of the grass. Make several passes so that no
more than 4cm of grass are cut at one time.
Switch off the motor, pull the safety plug (12)
and remove the batteries (16) before doing any
checks on the blade. Keep in mind that the bla-
de continues to rotate for a few seconds after
the motor has been switched off . Never attempt
to manually stop the blade. Regularly check to
see if the blade is securely attached, is in good
Anl_GP_CLM_47_S_HW_Li_SPK7.indb 29 Anl_GP_CLM_47_S_HW_Li_SPK7.indb 29
GB
condition and is sharp. If the contrary is the case,
sharpen the blade or replace it. In the event that
the blade strikes an object, immediately switch
off the lawn mower and wait for the blade to come
to a complete stop. Then inspect the condition of
the blade and the blade mount. Replace any parts
that are damaged.
As soon as grass clippings start to trail the lawn
mower, it is time to empty the grass basket. Cau-
tion! Before taking off the grass basket, switch off
the motor and wait until the blade has come to a
stop. Pull out the safety plug (12).
To take off the grass basket, use one hand to lift
up the chute fl ap and the other to grab onto the
basket handle. Remove the basket. For safety
reasons, the chute fl ap automatically falls down
after removing the grass basket and closes off the
rear chute opening. If any grass remains in the
opening, it will be easier to restart the engine if
you pull the mower back approximately 1m.
Do not use your hands or feet to remove clippings
in or on the mower housing, but instead use suita-
ble tools such as a brush or a hand broom.
In order to ensure that the majority of grass clip-
pings are picked up, the inside of the grass bas-
ket must be cleaned after each use.
Reattach the catch bag only when the motor is
switched off , the safety plug has been pulled out
and the blade has stopped.
Lift up the chute fl ap with one hand and, holding
the grass basket by its handle with the other
hand, hang in the basket from the top.
7. Cleaning, maintenance and
ordering of spare parts
Hazard!
Pull out the safety plug and remove all the battery
packs (16) before starting any cleaning work (Fig.
17/Item 8, Fig. 28).
7.1 Cleaning
•
To make it easy to clean, fold down the push
bar and move the equipment into the cleaning
position. (Fig. 17)
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
- 29 -
07.09.2022 13:06:33 07.09.2022 13:06:33