Installation Of Kwl 60 Dr Compensation Ring; Functional Description To Menu Tree; Comfort Controller Kwl 60 Bc - Helios KWL EC 60 Pro Montage- Und Betriebsvorschrift

Installation and Operating Instructions
EN
CHAPTER 4
COMFORT CONTROLLER
KWL-BCU/KWL-BCA
Wall installed unit KWL EC 60 Pro / ... Pro FF
3 .4

Installation of KWL 60 DR compensation ring

attach extension
sleeve to wall sleeve
attach partition elements
Trennsteg auf das Gehäuse
der Lüftungseinheit aufstecken
to the extension sleeve
4 .0 Functional description to menu tree of comfort controller KWL-BC . .
A1 = Initial start-up:
The following queries are carried
out at initial start-up:
1 .) Controller address: In case that
only one controller is connected,
address 1 can be used . If several
controllers (max . 4) should be con-
nected, each controller must be
assigned to an address of its own
(see point D8) .
2 .) Language: Selection: German,
English, French or Italian (see
point D8) .
3 .) Date and time: Setting of the
current date and time (see point
D9) .
Master / Slave – Mode:
Via Dip-switch 1 – on/off (see wiring
diagram SS-950), a KWL-unit can be
defined as a Master- or Slave unit.
It is to be noted that in the network
only one Master-unit is defined. The
remaining KWL-units must be defi-
ned as Slave-units, which are then
subordinated to the Master automa-
tically.
Thus one or more KWL-units (max.
10, see wiring diagram SS-958) can
be operated via the control system.
B5-B14 = Auto / Manual – Mode:
The speed control of the KWL-unit is
carried out by an automatic or manu-
al power control. In the automatic
mode the speed control takes place
in dependence of the room humi-
dity, the CO -concentration and/or
2
the weekly program. For this acces-
sory components like CO
respectively humidity sensor must
the connected.
In the manual mode the speed cont-
rol is carried out individually. By turn-
ing of the rotating encoder knob the
following levels can be selected:
Level 0-1-2-3-4-intake air-extract air.
Wandring auf
Wandhülse
aufstecken
Attach extension of Verlängerung
Kondensatablauf
condensate drain
aufstecken
Wand
fasten compensation
Distanzrahmen an der
Außenwand befestigen
ring to external wall
(Befestigungsschrauben
(fastening screws
aus Edelstahl bauseits)
from stainless steel
not provided by Helios)
If the CO -concentration rises over
2
1600 ppm or the humidity value is
over 80 % relative humidity, an infor-
mation "humidity alarm" or "CO
alarm" appears, i.e. the selected
speed step is insufficient.
C1 = Booster mode:
After activating the booster mode,
the KWL EC Pro operates in the pre-
set speed step. The remaining runti-
me in the booster mode is shown in
the display and can be deactivated at
any time. Over submenu D3 (boos-
ter), speed step and booster runtime
(1 - 180 minutes) can be set indivi-
dually.
C2 = Whisper mode:
After activating the whisper mode,
the KWL EC Pro operates in the pre-
set speed step. The remaining runti-
me in the whisper mode is shown in
the display and can be deactivated
at any time. Over submenu D4 (whi-
sper mode), speed step and booster
runtime (1 - 180 minutes) can be set
individually.
C4 = Clock timer:
It is possible to select between 6
already preset weekly programs: WP
1, WP 2, WP 3, WP 4, WP 5, WP
OFF. Select and confirm the desired
WP in the submenu C4.1 (standard
weekly program) for this purpose. If
an individual weekly program is to be
created, this can be specified in the
submenu 4.2 (individual weekly pro-
gram) for each weekday.
- sensor
2
C5 = Vacation program:
For example a firm vacation date can
be deposited over the menu vacation
program. For this time duration an
individual ventilation process can be
set. At the beginning of the vacation
it starts automatically and switches
off again independently. The result is
an ideal ventilation of your property
during this time.
4
fig .10
cut extension sleeve and
Wandring und Trennsteg
partition element flush
bündig mit Distanzrahmen
with compensation ring
abschneiden
compensation ring
Distanzrahmen
cut condensate drain
Kondensatablauf
SS-932
to 20 mm excess mit 20 mm Überstand
zum Distanzrahmen
length to wall
ablängen
~ 104
C6 = Sensor values:
A humidity sensor is factory-installed
in the unit. The humidity values are
- manually adjustable and are display-
2
ed in the graphic display of the con-
troller.
Furthermore, up to four CO
sors (accessories: KEL-CO
No. 9988) for detection of the CO
concentration in the indoor air can be
connected and displayed.
C7 = Settings:
Over the setup menu several para-
meters can be adjusted individually.
D1 = Humidity control:
The most important functions are
defined in the submenu D1.
If the humidity control is activated,
the ventilation control takes place
as a function of the relative humidi-
ty, which is measured directly in the
extract air. Following individual set-
tings are possible:
Setpoint: Setting of relative humidity
for level 1.
Switching steps: Switching threshold
in next level run on time: If the set-
point is not reached within 2 hours,
a mandatory pause takes place from
0 to 24 hours, in order to prevent a
continuous running.
D6=Supply and extract air level:
The supply and extract air level can
be set individually.
D7 = Filter change:
The interval for changing the filter can
be set between 2 till 9 months. The
remaining period for a filter change
can be displayed by a query. With an
earlier filter change, the remaining
period must be reset.
-sen-
2
, Ref.
2
2