Contents Welcome Safety Instructions Laser Module Introduction Package List Size Diagram Laser Control Module Installation Guide for 3018-PRO & 3018-PROVer Installation Guide for 3020-PRO MAX Installing LaserGRBL Use LaserGRBL to Focus the Laser CE und Safety Certificates of Compliance...
Welcome Dear customer, Thank you for purchasing the Genmitsu 5.5W compressed spot laser fixed focus module. This 5.5W diode laser with a wavelength of 445nm is especially designed for use with the Jinsoku LC-60A, LE-1620 Laser Engraver and Genmitsu PROVerXL 4030 CNC Machines.
Safety Instructions Always exercise safety and caution when working with laser marking systems. Consider the listed recommendations to minimize risk. · You must be at least 13 years old to operate the laser engraver. · Direct exposure to the laser beam can cause severe burns and eye damage. Ensure that you are wearing proper laser safety goggles when working in the vicinity of the laser equipment.
Package List 3018-PRO Connection Connection Cable, Laser Module with Focus Calibration Cable, Suitable for Suitable for controller with Air Assist Nozzle Tool, 30mm controller with 12V GND PWM terminal 12V PWM terminal Safety Goggles (Green), 12V Power Supply Power Cord(US/EU) Power Adapter(UK) FDA-Certified M3 T-nut...
Laser Control Module The Laser Control Module matching the Laser Head contains the necessary control electronics for processing the PWM signal applied to the input. This results in the laser being supplied with the required voltage at the right time. The Laser Control Module can be mounted to the 2020 aluminum profiles normally used on milling and engraving machines by means of the supplied T-nuts and M3 screws.
Seite 9
Laser Control Module On the other side of the Laser Control Module there is a number of connectors and a press switch. • External 12V DC 5A power source. • Fire / PWM Button, when in this is pressed 12V DC power in the laser is permanently on at 100% power, when out the laser power is controlled by the PWM signal.
Installation Guide for 3018-PRO & 3018-PROVer STEP 1: Remove the Spindle Motor 1. Pull out the two cables on the spindle motors as illustrated. 2. Loosen the M4 screw on the spindle holder and then remove the spindle as illustrated. pull pull Spindle Motor...
Seite 11
Installation Guide for 3018-PRO & 3018-PROVer STEP 2: Install the Laser Head 1. Raise the spindle holder to the top. 2. Push the laser module controller through the spindle holder. 3. Align the four corners of the laser module with the square slots, and then push the laser head into the spindle holder.
Seite 12
Installation Guide for 3018-PRO & 3018-PROVer STEP 3: Install the Laser Module Controller 1. Slide an M3 T-nut into the aluminum profile. 2. Insert an M3*8 screw into the laser module controller and adjust the controller position,make sure the M3*8 screw and M3 T-nut is aligned then tighten the screw with two rotations.
Seite 13
Installation Guide for 3018-PRO & 3018-PROVer STEP 4: Cable Connection 1. 3018-PROVer: Plug one end of the 2-pin connector into the PWM port of the machine controller and the other end into the PWM port of the laser module controller; Plug the 12V power cable into the 12V DC power jack. 2.
Installation Guide for 3020-PRO MAX STEP 1: Remove the Spindle Motor 1. Pull out the two cables on the spindle motors as illustrated. 2. Loosen the M5 screws on the spindle holder and then remove the spindle as illustrated. Spindle motor cables pull Spindle holder Spindle Motor...
Seite 15
Installation Guide for 3020-PRO MAX STEP 2: Install the Laser Head 1. Insert the laser module holder into the spindle holder. 2. Align the four corners of the laser module with the square slots, and then push the laser head into the spindle holder.
Seite 16
Installation Guide for 3020-PRO MAX STEP 3: Install the Laser Module Controller 1. Slide an M3 T-nut into the aluminum profile. 2. Insert an M3*8 screw into the laser module controller and adjust the controller position, make sure the M3*8 screw and M3 T-nut is aligned then tighten the screw with two rotations.
Seite 17
Installation Guide for 3020-PRO MAX STEP 4: Cable Connection 1. 3020-PRO MAX: Plug one end of the 2-pin connector into the 12V PWM GND port of the machine controller and the other end with the 12V power and PWM port. 12V Power and PWM Control 12V PWM GND...
Installing LaserGRBL LaserGRBL is a free program which works with Grbl based routers fitted with a Laser and Laser Engravers. It will be used here to assist with setting up the Laser, though it is capable of both sending GCode and converting images to G-Code for Laser Engraving It can be downloaded from https://lasergrbl.com/download/ After installation and connecting to the router the screen should look like this:...
Seite 19
Installing LaserGRBL There are a couple of customizations to be made before proceeding. Enable Z axis Jog...
Seite 20
Installing LaserGRBL Add Custom buttons FIX URL Download the file CustomButtons.gz from our SainSmart WIKI at the following URL: https://lasergrbl.com/usage/custom-buttons/ . click Open. The dialog box of Import custom button will appear. A short dialog is displayed for each of the three additional buttons. You can now select for each individual button...
Seite 21
Installing LaserGRBL The LaserGRBL window should now look like this. The three added buttons are arranged from left to right and contain the following functions: Tun on laser at low power (S100), press Router Connection again to turn off. Console Output Set for Laser mode Console Output ($32=1)
Use LaserGRBL to Focus the Laser To cut or engrave efficiently we want the laser beam to be tightly focused into the smallest possible point at the top of the stock. Although the focus point of the Laser is fixed the height of the laser above the stock needs to be set correctly.
Seite 23
Use LaserGRBL to Focus the Laser If desired test the focus of the laser by placing something which will not burn of a known thickness on top of stock underneath the laser. Click the Laser Fire button to turn the Laser On Focused No focused If necessary use the Z-Axis Adjustable Knob to move the Laser up and down to achieve the smallest possible...
Seite 24
Inhalt Willkommen Warnhinweise Technische Daten Lieferumfang Größentabelle Laser Steuerbaugruppe Einbau des Lasers in eine 3018-PRO & 3018-PROVER Einbau des Lasers in eine 3020-PRO MAX Installation von LaserGRBL Verwendung von LaserGRBL zur Laserfokussierung CE und Safety Certificates of Compliance...
Willkommen Sehr geehrter Kunde, vielen Dank, dass Sie sich für das Genmitsu 5.5W Laser-Fixfokus-Modul entschieden haben. Dieser blaue 5,5 W Diodenlaser mit einer Wellenlänge von 445 nm ist speziell für den Einsatz mit den Jinsoku LC-60A, LE-1620 Laser-Graviermaschine und Genmitsu PROVerXL 4030 CNC-Fräs-/Graviermaschine.
Warnhinweise Gehen Sie bei der Arbeit mit Lasermarkierungssystemen stets umsichtig und vorsichtig vor. Beachten Sie die aufgeführten Empfehlungen, um das Risiko von Schäden zu minimieren. Sie müssen mindestens 13 Jahre alt sein, um den Lasergravierer zu bedienen. Direkter Kontakt mit dem Laserstrahl kann zu schweren Verbrennungen und Augenschäden führen. Stellen Sie sicher, dass Sie eine geeignete Laserschutzbrille tragen, wenn Sie in der Nähe des Lasergeräts arbeiten.
Laser Steuerbaugruppe Die zum Laserkopf passende Laser-Steuerbaugruppe enthält die erforderliche Steuerelektronik zur Verarbeitung des am Eingang anliegenden PWM-Signals. Dadurch wird der Laser zur richtigen Zeit mit der benötigten Spannung versorgt. Mit den mitgelieferten Nutsteinen nebst Schrauben kann die Laser-Steuerbaugruppe an den in der Regel bei Fräs-/Graviermaschinen verwendeten 2020er Alu-minium-Profilen befestigt werden.
Seite 31
Laser Steuerbaugruppe Auf der anderen Seite des Lasersteuerungsmoduls befinden sich eine Reihe von Anschlüssen und ein Druckschalter. • Externe 12V DC 5A Stromquelle. 12V Gleich- • Feuer-/PWM-Schalter; wenn dieser stromversorgung eingedrückt ist, so ist der Laser dauerhaft mit 100 % Leistung eingeschaltet, wenn er nicht gedrückt ist, wird die Laserleistung hingegen durch das PWM-Signal gesteuert.
Einbau des Lasers in eine 3018-PRO & 3018-PROVER Schritt 1: Spindelmotor entfernen 1. Trennen Sie die beiden Kabel an den Spindelmotoren wie im Bild gezeigt. 2. Lösen Sie die M4-Schraube am Spindelhalter und entfernen Sie die Spindelmotor. ziehen ziehen Spindelmotor Kabel des Spindelmotors Spindelhalter ziehen...
Seite 33
Einbau des Lasers in eine 3018-PRO & 3018-PROVER Schritt 2: Einbau des Laserkopfs 1. Bewegen Sie die Motorhalterung mithilfe der Jog-Steuerung in die höchste Höhe. 2. Schieben Sie den Laserkopf so in die Motorhalterung, dass die Ecken in den Schlitzen der Motorhalterung liegen und das Kühlgebläse des Laserkopfs nach oben zeigt.
Einbau des Lasers in eine 3018-PRO & 3018-PROVER Schritt 3: Einbau der Laser-Steuerbaugruppe 1. Setzen Sie den Nutenstein M3 im Aluminiumprofil der Rückseite der CNC-Fräs-/Graviermaschine ein. 2. Setzen Sie eine M3 Schraube in den Laser-Steuerbaugruppe ein und stellen Sie die Position der Steuerbaugruppe der CNC-Fräs-/Graviermaschine ein.
Einbau des Lasers in eine 3018-PRO & 3018-PROVER Schritt 4: Anschluss an eine 3018-PRO & 3018-PROVer 1. 3018 PROVER: Schließen Sie das 2-poligen Kabel an den PWM der 3018-PROVer und den PWM des Lasersteuermoduls an. Dann schließen Sie das 12V-Netzkabel an die 12V-Gleichstromversorgung an. 2.
Einbau des Lasers in eine 3020-PRO MAX Schritt 1: Spindelmotor entfernen 1. Trennen Sie die beiden Kabel an den Spindelmotoren wie im Bild gezeigt. 2. Lösen Sie die M5-Schraube am Spindelhalter und entfernen Sie die Spindelmotor. Kabel des Spindelmotors pull Spindelhalter Spindelmotor M5 Schraube...
Seite 37
Einbau des Lasers in eine 3020-PRO MAX Schritt 2: Einbau des Laserkopfs 1. Setzen Sie den Lasermodulhalter in den Spindelhalter ein. 2. Schieben Sie den Laserkopf so in die Motorhalterung, dass die Ecken in den Schlitzen der Motorhalterung liegen und das Kühlgebläse des Laserkopfs nach oben zeigt. 3.
Seite 38
Einbau des Lasers in eine 3020-PRO MAX Schritt 3: Einbau der Laser-Steuerbaugruppe 1. Setzen Sie den Nutenstein M3 im Aluminiumprofil der Rückseite der CNC-Fräs-/Graviermaschine ein. 2. Setzen Sie eine M3 Schraube in den Laser-Steuerbaugruppe ein und stellen Sie die Position der Steuerbaugruppe der CNC-Fräs-/Graviermaschine ein.
Seite 39
Einbau des Lasers in eine 3020-PRO MAX Schritt 4: Anschluss an eine 3020-PRO MAX 1. 3020-PRO MAX: Anschließen des Lasersteuermoduls an eine 3018-PRO MAX unter Verwendung des 2-poligen Kabels für GND und PWM und der mitgelieferten externen Stromversorgung für das Laser-steuermodul.
Installation von LaserGRBL LaserGRBL ist ein kostenloses Programm, das mit GRBL-basierten CNC Fräs-/Graviermaschinen arbeitet, die mit einem Laser und Lasergravierern ausgestattet sind. Es wird hier verwendet, um bei der Einrichtung des Lasers zu helfen, obwohl es in der Lage ist, sowohl G-Code zu senden als auch Bilder für die Lasergravur in G-Code zu konvertieren.
Seite 41
Installation von LaserGRBL Bevor Sie fortfahren, müssen Sie einige Anpassungen vornehmen. Z-Aufwärts/Abwärts-Steuerung anzeigen Sie sich, dass das Kontrollkästchen "Z-Aufwärts/Abwärts-Steuerung anzeigen" aktiviert ist, und speichern Sie die Einstellung.
Seite 42
Installation von LaserGRBL Benutzerdefinierte Schaltflächen hinzufügen Unter dem URL http://wiki.sainsmart.com/index.php/SainSmart_Blue_Laser_Kit . laden Sie sich zu-nächst aus unserem WIKI die Datei „CustomButtons.gz“ herunter. Klicken Sie anschließend mit der rechten Maustaste auf den Text „Right click here to add custom buttons“ in der Schaltflächenleiste von LaserGRBL und wählen Sie „Import custom buttons“.
Seite 43
Installation von LaserGRBL Das LaserGRBL-Fenster sollte nun wie folgt aussehen. Dabei sind die drei hinzugefügten Schalt-flächen von links nach rechts angeordnet und beinhalten die folgenden Funktionen: Laser bei niedriger Leistung (S100) einschalten, zum Ausschalten erneut betätigen. Lasermodus einschalten ($32=1) Laser bei niedriger Leistung (S100) für 2 Sekunden einschalten, danach wieder ausschalten (nützlich bei der Einstellung einer Ursprungsposition)
Verwendung von LaserGRBL zur Laserfokussierung Um effizient zu schneiden oder zu gravieren, muss der Laserstrahl so genau wie möglich auf einen möglichst kleinen Punkt fokussiert werden. Obwohl der Fokuspunkt des Lasers fixiert ist, muss der Abstand des Lasers über dem Material korrekt eingestellt werden. Vergessen Sie nicht, dabei die Schutzbrille zu tragen. •...
Seite 45
Verwendung von LaserGRBL zur Laserfokussierung Falls gewünscht, testen Sie die Fokussierung des Lasers, indem Sie etwas nicht brennbares Material mit einer bekannten Dicke auf die Fläche unter dem Laser legen. Verwenden Sie nun die Z-Achsen-Jog-Steuerung, um die Dicke des auf dem Material platzierten Gegenstands zu erhöhen. Klicken Sie auf die Schaltfläche „...