Tr4000 4 Et I Tr4000R 4 Et; Płukanie Rozruchowe; Regulowanie Temperatury; After Installation - Bosch TR4000 Montage- Und Gebrauchsanleitung

After installation

3 After installation
3.1

TR4000 5 ET, TR4000 6 ET, TR4000 6 EB,

TR4000 8 ET and TR4000 8 EB
(fixed electrical connection)
Switch on the fuses.
3.2 TR4000 4 ET and TR4000R 4 ET
• Insert the plug into the mains socket.
First start-up
(Fig. 6)
3.3

Initial rinsing

• Open the warm water tap and allow water to flow for at least
1 minute (flow-rate at least 2 litres per minute). Only then
(for safety reasons) will the appliance begin to heat.
Info: The appliance will not heat if the dispensed water flow is
interrupted prematurely. Open the warm water tap again and
allow water to flow for at least 1 minute.
4

Technical data

Type
Design
Power
Electrical connection
Minimum cable cross-section [mm²]
Rated current
Fuse protection
Water connection thread
Supply temp. max.
Warm water output at supply
temp. of 12 °C to 38 °C
Protection type
Switch on flow pressure
(without flow rate limiter)
Switch on flow
Switch off flow
18
TR4000 4
ET
TR4000R 4
ET
Undersink
pressurised pressurised pressurised pressurised pressurised pressurised
[kW] 3,6
[V] 230
1,5
[A] 15,7
[A] 16
[Inch] G 3/8
[°C] 20
[l/min] 1,9
IP 24
[bar] < 0,3
[l/min] 1,8
[l/min] 1,6
Tip: Should the appliance not start because of a reduced flow-
rate, remove the perlator, aerator or similar before starting and
repeating the process.
Important: If the continuous-flow heater does not have
sufficient water flow due to low water line pressure in your
domestic plumbing system:
• Switch off the circuit-breakers/fuses or remove the mains
plug.
• Remove the flow-rate limiter (H1–H4).
3.4

Controlling temperature

The supply temperature (probably lower in winter) and
pressure fluctuations can influence the temperature of the
water leaving the tap (see Fig. 4, left: pressurised [closed],
right: unpressurised [open]).
• Turn the valve slowly in the closed direction for higher
temperatures (F1).
• Add cold water for lower temperatures (F2).
• Hand over the installation and operating instructions
to the user and explain how the appliance operates.
TR4000 5 TR4000 6
ET ET
Undersink Undersink
4,5 6
230 230
2,5 4
19,1 26
20 32
G 3/8 G 3/8
20 20
2,4 3,2
24 24
< 0,3 < 0,3
1,8 / 1,9 1,8 / 2,1
1,6 / 1,7 1,6 / 2,0
TR4000 | TR4000R – 6720876021 (2022/04)
TR4000 8 TR4000 6
ET EB
Undersink Over-sink
7,2 6
230 230
4 4
31,3 26
32 32
G 3/8 G 1/2
20 20
3,9 3,2
24 24
< 0,3 < 0,3
1,8 / 2,3 1,8 / 2,1
1,6 / 2,2 1,6 / 2,0
TR4000 8
EB
Over-sink
7,2
230
4
31,3
32
G 1/2
20
3,9
24
< 0,3
1,8 / 2,3
1,6 / 2,2