Setting Timer; Other Functions; Setting The Swing Function; Changing Over Display And Alarm Buzzer (Mute Mode) - Bosch CL6001iU W 70 E Bedienungsanleitung Für Den Betreiber

Change set humidity during dehumidification mode:
▶ Press Humidity key repeatedly until the desired maximum humidity
is reached. The setting range is 35 % - 85 % in 5 % steps.
The set humidity is shown in the display.
Heating mode
▶ Press Mode key repeatedly until
▶ Set the required temperature with the . and / keys.
▶ Press the key until the required fan speed is reached.
If the outside temperature is very low, the heating capacity of the air
conditioning system may not be sufficient. We recommend connecting
additional heat sources.
3.5

Setting timer

ON and OFF timers can be set to between 0 and 24 hours, in 30-minute
increments for the first 10 hours, then in 1-hour increments. If 0 hours is
set, the timer is cancelled.
Setting the on timer
▶ Press the key until the
▶ Press the . or / key to set the desired time.
The setting is applied shortly afterwards.
Setting the off timer
▶ Press the key until the
▶ Press the . or / key to set the desired time.
The setting is applied shortly afterwards.
Cancelling timer
▶ Press the key to select the corresponding timer.
▶ Set 0.0 hours.
The timer is cancelled after a short time.
Combining timers
The two timers can be set at the same time. Either timer can be
programmed to activate prior to the other
▶ Set the on timer and off timer.
The settings will be automatically combined.
Current time
Setting of ON timer
Setting of OFF timer
Switch-on time
Switch-off time
Table 7 Example
You can not program the on timer and off timer to operate the unit at
different temperatures or with other settings.
Climate 6000i – 6721838271 (2022/11)
appears on the display.
symbol appears.
symbol appears.
13:00 o'clock
4.0 h
8.5 h
17:00 o'clock
21:30 o'clock
3.6

Other functions

3.6.1

Setting the swing function

NOTICE
If the louver remains at the lowest position during cooling mode for an
extended period, condensate may form. Adjusting the louver by hand
may cause faults.
▶ Only use the remote control to adjust the louver.
Automatic vertical swing mode (up/down)
▶ Press the Swing key until the symbol
▶ To cancel the automatic vertical Swing mode: press the Swing key
again.
Swivelling the louver manually (up/down)
▶ Press the Swing key until the required position is set.
The setting changes in the following sequence:
Automatic horizontal swing mode (left/right)
▶ Press the Swing key for longer than 2 seconds to activate the
automatic horizontal Swing mode.
The remote control displays the symbol
▶ To cancel the automatic horizontal Swing mode: press the Swing key
again.
Cleaning position
To make cleaning easier, the louver can be brought into a special position
(depending on model).
▶ Press the Mode and Swing keys simultaneously for one second when
the unit is switched off.
▶ To exit the cleaning position: press and hold both keys again.
3.6.2

Changing over display and alarm buzzer (Mute Mode)

▶ To switch on or off the display at the indoor unit and the alarm buzzer:
press LED key.
▶ To display the current room temperature, press the LED key and hold
for 5 seconds.
▶ To display the set temperature: press and hold the LED key for
another 5 seconds.
3.6.3

Energy saving functions

The following energy saving functions can be selected at the unit:
1)
• ECO : operation with fan speed AUTO and set temperature of at
least 24 °C
• GEAR (75%): reduce power consumption by 25 %
• GEAR (50%): reduce power consumption by 50 %
• None of the above symbols: normal operation
▶ To activate an energy saving function, press
required function is displayed.
The ECO function automatically sets a temperature of 24 °C if the
previously set temperature is lower. The function switches off as soon as
the temperature is lowered to less than 24 °C.
1) Only in cooling mode
Operation
appears.
.
key until the
57