Care And Cleaning; Technical Data - Renkforce 2377497 Bedienungsanleitung

h) Indicator light
Indicator light
Red and blue LED flash quickly
alternately
Red and blue LED flash quickly
Headset
alternately
Blue LED flashes once every 5 seconds
Blue LED flashes twice every 10 seconds
Red LED flashes twice every 10 seconds
When the charger is not connected and
the headset is not on the station, the
power indicator on the charging station is
gray and white.
The station is connected to a Bluetooth
device and the power button LED is white.
The headset is connected to a Bluetooth
device, and the white light on the power
Charging
button flashes slowly.
station
The charging station has no indicator light
when the headset is placed on the station.
The red light is on during the charging
process.
The red light goes off after charging is
complete.
The white LED indicator on the mute
button is flashing.
i) Factory reset
Put the headset into the station for charging and quickly press the headset MFB button 5 times.
The headset's red and blue lights will flash quickly and the station's 4 lights will flash at the
same time.
Press the headset MFB button 5 times.
Note:
• After a factory reset, the paired list of Bluetooth devices will be deleted, and the headset will
not automatically reconnect to any previously connected Bluetooth device.
• After a factory reset, when the headset turns on again, it will automatically enter pairing
mode (red and blue lights flash fast).
j) Care and maintenance
Read the following recommendations carefully before using the unit.
• Use and store the unit in a dry environment to prevent the internal circuit from becoming
damaged. Do not wear the headset during exercise to avoid damage from sweat.
• Clean the headset before putting it into the charging station to prevent sweat from corroding
the product.
• Keep the product away from direct sunlight or hot conditions. High temperatures may
shorten the life of the device, destroy the battery or distort certain plastic parts.
• Do not expose the product to cold conditions.
• Do not attempt to disassemble the product.
• Do not let the product fall onto the floor or other hard surfaces.
• Do not use abrasive chemical products or detergents to clean the product.
• Do not scratch the surface of the product with sharp items.
If the product does not function properly, contact your retailer for assistance.
k) Troubleshooting
1. What does it mean when the LED flashes slowly in red twice every 10 seconds?
The battery is low and needs to be charged.
2. Why is the red LED off during the charging process?
a) The charging station may not have enough battery power to charge the headset and needs
to be charged.
b) Make sure the metal contacts on the headset and charging station are free of obstacles.
c) The battery may need to be charged. Charge the battery for 30 minutes, after which the
red LED should be on.
3. Why can't I hear sound through the headset?
a) Make sure the volume is not too low or muted.
b) Make sure the headset is properly connected to the Bluetooth device.
c) Make sure the headset and the Bluetooth device are within range.
Status
4. Why can't I hear sound clearly on the headset?
Pairing with Bluetooth
a) Make sure the Bluetooth device is within range.
device
b) Make sure the headset is within range and there are no obstacles in the way.
Pairing with station
5. Why do the pause/play functions not work when playing music?
(very short duration)
Make sure your Bluetooth device supports AVRCP (Audio/Video Remote Control profile).
Not connected
Connected

Care and cleaning

Low battery
• Disconnect the product from the mains before cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol, or other chemical solutions as
Idle state
• Clean the product with a dry, fibre-free cloth.
Disposal
Connected to a Bluetooth
device Product
Connected to the headset,
but the station is not
connected to a Bluetooth
device
You thus fulfill your statutory obligations and contribute to the protection of the environment.
The headset is charging

Technical data

The station is charging
Chipset ............................................... QCC3020 (headset)
The station is fully charged
Bluetooth version ................................ V5.1 (headset)
The mute function is on
Bluetooth profile .................................. A2DP V1.3,AVRCP V1.6,HFP V1.7, HSP V1.2
Bluetooth name .................................. RF-WE-510
Paired Bluetooth devices .................... Max. 4 simultaneously
Bluetooth transmission frequency ...... 2.402-2.480 GHz, 2.4G ISM Band
Frequency Response ......................... 20-20 KHz
Drive unit of the speaker ..................... D10 mm/32 Ω/3 mW
Talk/Music time ................................... 4-5 hours (volume <50%)
Standby time ....................................... Max. 190 hours
Mono headset battery ......................... 3.7 V, 55 mAh
Charging station battery ..................... 3.7 V, 650 mAh
Charging time (headset) ..................... Approx. 1.5 hours
Charging time (station) ....................... Approx. 2 hours
Speaker impedance ............................ 32 Ω
Distortion ............................................ < 5% [< 1%(150 mV pk-pk Input)]
Transmitted power for transmitter ....... 4 dBm
Microphone type ................................. Two Omnidirectional
Microphone frequency response ........ 100-10,000 Hz
Microphone sensitivity ........................ -42±2 dB
Operating/storage conditions .............. -10 °C to +45 °C
Dimensions (W x H x D) ..................... 12 x 110 x 28 mm (headset)
Weight ................................................ 97g (charging station)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2021 by Conrad Electronic SE.
they can cause damage to the housing and functioning of the product.
Electronic devices are recyclable waste and must not be disposed of in household
waste. At the end of its service life, dispose of the product in accordance with
applicable regulatory guidelines.
BLE (charging station)
V4.2 (charging station)
87 dB SNR
< 5% [< 1%(150 mV pk-pk Input)] THD
10 % to 90 % RH (non-condensing)
86 x 46 x 118 mm (charging station)
9.4g (headset)
*2377497_v2_1021_02_DS_m_4L_(1)