Renkforce 2377497 Bedienungsanleitung Seite 5

c) Connecting the headset to Bluetooth devices (Paired with 1 device only)
Each headset can be worn singly as a Bluetooth headset.
1. Power on
• The business headset will turn on automatically when removed from the charging station.
• If the headset is powered off, press the MFB press button for about 3 seconds until the blue
LED flashes and "Power on" is played through the headset.
2. Pairing
• Press and hold the MFB button for about 5 seconds in the off state and release it when you
see the red and blue lights flash alternately. A "Pairing" voice prompt will also be played
through the headset.
3. Connecting
When the headset is in pairing mode, search for the corresponding Bluetooth device name
(see below) from the Bluetooth device list and connect. "Connected" will be played through
the headset after the devices have been paired.
Bluetooth device name: RF-WE-510
4. Powering off
• The headset powers off automatically once connected to the charging station.
• Press the MFB button for about 5 seconds and release it when the red LED lights up.
"Power off" will play through the headset.
Note:
• Each business headset will automatically switch to standby mode if disconnected from the
device (the blue LED will flash once every 2 seconds) and will power off automatically after
5 minutes to save power.
• Pairing mode is enabled for 2 minutes. If the headset does not pair with a device within
2 minutes, it will power off automatically.
d) Connecting the charging station to Bluetooth devices (Paired with up to
4 devices)
1. Connection method
Turn on the headset and take it off the charging station, and then enable pairing mode
on the charging station. If you want to connect multiple bluetooth devices, press and hold
button (10) / (11) / (12) / (13) on the station for about 3 seconds. When the white light
flashes, release the button, the station will into pairing mode.
2. Switching devices
When multiple Bluetooth devices have been connected to the charging station, you can
switch between them. Press and hold the button corresponding to the Bluetooth device
you want to switch for 2 seconds. The white light will light up, indicating that the Bluetooth
device has been switched.
e) Pairing the headset with the charging station (if not automatically paired)
1. Turn on the headset and the station separately.
2. Clear the pairing list
Put the headset into the station to charge (so the headset is charging) and quickly press the
headset function button 5 times. The red and blue lights on the headset will flash quickly
and the 4 lights on the station will flash at the same time. The headset and the station will
automatically connect.
3. Connecting the headset to a new station
Quickly press the first function key on the station 5 times. The 4 indicator lights on the
station will flash at the same time. Then turn on the headset and press the function key
5 times. The indicator light will flash red and blue and the new station will automatically
connect.
Note:
• The headset is paired with the station before shipping. Under normal circumstances, you
only need to take the headset out of the charging station and it will automatically connect.
• If the headset does not automatically connect after being taken out of the charging station,
follow the above steps to re-establish the connection between the headset and the station.
f) Headset functions
1. Music
Function Headset status
Press the MFB
Play Paused music
Press the MFB
Pause Playing music
Previous
Playing music
track
Next track Playing music
Volume + Playing music
Volume - Playing music
Voice Connected to
assistant device MFB (4) button
2. Calling
Function Headset status
Cancel call Calling
Incoming call
Reject call
ringing
Incoming call
Answer call
ringing
End call During a call
Switch voice to
Calling
phone
Switch voice to
Calling
headset
Volume + During a call
Volume - During a call
g) Battery display
When the headset is connected to an iOS device, the headset battery level will be displayed
on the device. When the headset is low on power, the battery indicator will turn red and
show a depleted battery icon. An audio prompt will also be given to remind you to charge
your headset.
Full charge:
RF-WE-510
Headset Charging station
operation operation
Press the Power
(4) button (13) button
Press the Power
(4) button (13) button
N/A N/A
N/A N/A
N/A Press the + button
N/A Press the - button
Triple-press
N/A
Charging
Headset
station
operation
operation
Press the MFB
N/A
(4) button
Double-press
the MFB (4)
N/A
button
Press the
Press the MFB
Power (13)
(4) button
button
Press the
Press the MFB
Power (13)
(4) button
button
N/A N/A
N/A N/A
Press the +
N/A
button
Press the -
N/A
button
Low battery:
RF-WE-510
Prompt tone
Beep
Beep
N/A
N/A
N/A
N/A
Beep
Prompt tone
Beep
Rising tone
Falling tone
Beep
N/A
N/A
beep
beep