Product Description; Stopping And Turning Off The Robot Lawn Mower In Safe Conditions - Stiga G 300 Bedienungsanleitung

1.2. PRODUCT DESCRIPTION

The robot lawn mower is designed to mow the grass around
areas of the garden delimited by the perimeter cable.
The operating principle is based on random navigation. The
robot lawn mower changes trajectory whenever the perimeter
cable or an obstacle is detected.
Any other usage may be hazardous and harm persons and/
or damage things. Improper use includes (for example, but
not limited to): transporting people, children or animals on
the machine; being transported by the machine; using the
machine to pull or push loads; using the machine for cutting
non-grass vegetation.
1.3. SYMBOLS AND NAMEPLATES
WARNING:
Read the user instructions before starting
the product.
WARNING:
Danger of projections of objects against
the body.
Keep an adequate safe distance from the
machine while it is running.
WARNING:
Do not put hands and feet near or under the
opening of the cutting means.
Remove the disabling device before operating
on the machine or before lifting it.
WARNING:
Do not put hands and feet near or under the
opening of the cutting means.
Do not stand on the machine.
BAN:
Make sure that there are no people (especially
children, elderly or disabled) and pets in the
working area during the operation of the
machine.
Keep children, pets and other people at a safe
distance when the machine is functioning.
BAN:
Do not use high pressure cleaners on the
machine to clean or wash it.
1.4. STOPPING AND TURNING OFF THE ROBOT
LAWN MOWER IN SAFE CONDITIONS
OBLIGATION:
Always switch off the robot lawn mower in safe
conditions before any cleaning, transport or
maintenance operation.
1. Press the "STOP" push button (Fig. 1.A) to stop the robot
lawn mower safely and open the protective cover (Fig. 1.B).
2. Remove the safety key (Fig. 1.D) to switch off the robot
lawn mower in safe conditions.
3. Close the protective cover (Fig. 1.B).
4. The robot lawn mower is stopped or switched off in a
safe condition.
EN
2. INSTALLATION
WARNING:
Do not modify, tamper with, elude or eliminate
the safety devices installed.
NOTE: For further clarification on the installation of the
product please contact a STIGA dealer.
INSTALLATION COMPONENTS (Fig. 2)
(A) Charging base, (B) Power supply, (C) Perimeter cable,
(D) Perimeter cable fixing pegs, (E) Fixing screws for the
charging base, (F) Joint for perimeter cable, (G) Charging
base connectors
2.1. VERIFICATION OF THE INSTALLATION
REQUIREMENTS
2.1.1. GARDEN ASSESSMENT:
• Check the garden condition in accordance with Chap. 1.
• Level the ground so that no puddles form as a result of rain.
2.1.2. CHECKS FOR THE INSTALLATION OF THE
CHARGING BASE AND POWER SUPPLY:
ELECTRICAL HAZARD:
It is absolutely necessary to provide an
electrical outlet that complies with the relevant
laws of the country.
ELECTRICAL HAZARD:
The circuit provided must be protected by
a residual current device (RCD) with an
activation current not exceeding 30 mA.
ELECTRICAL HAZARD:
Do not connect the power supply to an
electrical outlet if the plug or the cable is
damaged.
Do not connect or touch a damaged cable
before it is disconnected from the power
supply.
A damaged cable can lead to contact with
live parts.
1. Provide a flat surface at the edge of the lawn to position
the charging base.
2. Ensure that the distance of the base from any bends is
at least 200 cm.
WARNING:
The power cable, power supply unit, extension
cord and all other electric cables which do not
belong to the product must remain outside the
cutting area to maintain their distance from
hazardous moving parts and prevent damage
to cables which may come into contact with
live parts.
3. Set up the installation area of the power supply unit in
such a way as to prevent it from being submerged by
water under all weather conditions. Preferably install in a
closed room and protected from weather conditions, in a
location not easily accessible by unauthorised persons.
2