Chapter 2 - Purposes / Intentions; Chapter 3 - Preparation (Unpacking) - Comet CSW 700 Bedienungs- Und Wartungsanleitung

Inhaltsverzeichnis

Verfügbare Sprachen

- Instructions and operating manual CSW 700 B/G - CSW 900 B/G (translated from original instructions)

Comet S.p.A. is pleased to make you the new owner of a CSW 700 - CSW 900 series sweeper.

By observing the instructions provided below, we are certain you will be able to fully appreciate the opera-

ting possibilities offered by CSW 700 - CSW 900.

This instructions manual is supplied to instruct and define the purposes and intentions that the machine

was designed for and its safe use, as clearly as possible.

You will also find a list of all of those minor operations required to keep CSW 700 - CSW 900 in good running

order and safe. Procedures that can easily be carried out by anyone.

Always seek the assistance of specialised staff for unscheduled maintenance.

You will find information on hazards and residual risks, i.e. all of those risks that cannot be eliminated, plus

adequate information on allowed and forbidden uses;

instructions on how to commission CSW 700 - CSW 900, technical instructions and allowed performance;

instructions on how to operate CSW 700 - CSW 900 and its maintenance; instructions on how to decommis-

sion the machine, and dismantle or demolish it.

Refer to figures 1 to 14, which are located at the start of these operating and maintenance

instructions

u UNPACKING:

Having eliminated the outer packaging, free the machine from the pallet as follows:

1. Release the front wheel brake WITH THE FOOT, NOT WITH THE HANDS!!!

2. Remove the sticky tape Detail C blocking the handlebar.

3. Open the bin Detail A and pull out the two handlebar supports Detail B Fig.1.

4. Screw the handlebar supports Part. B into the holes Part. E Fig. 1

5. Screw the ends of the handle into the holes Detail D on the supports as shown in Fig.1/B.

6. Take the machine off the pallet: according to the machine weight, written on the CE label, this can be

done in different ways.

a With the aid of one or more people provided with gloves, lift the machine, holding it by handle at

the front, and stand it on the ground.

b With the aid of a slanting board (longer than 80 cm not to damage the dust flaps) placed against the

narrowest side of the bench, slide the machine down until the floor.

IMPORTANT: All waste material from the unpacking operations must be disposed of by the user, in

accordance with the specific standards for disposal currently in force.

MAKE SURE THAT THE GUARDS ARE PERFECTLY INTACT AND SECURELY INSTALLED; IN CASE

OF FAULTS OR MISSING PARTS DO NOT PROCEED WITH COMMISSIONING AND PROMPTLY

ASK FOR SPARE PARTS FROM YOUR DEALER OR THE PARENT COMPANY.

u MONTAGGIO SPAZZOLA LATERALE:

1. Estrarre la spazzola laterale part. 2 fig. 2 dal cassetto di raccolta part. A fig. 1.

2. Svitare i tre bulloni part. 1 fig. 2; montare la spazzola inserendo i tre perni nei fori part. 3 fig. 2.

3. Riavvitare i tre bulloni part. 1 in modo da bloccare la spazzola.

4. Una volta montata, la spazzola laterale formerà a contatto con il part. 4 fig. 2 la puleggia in cui inserire la

cinghia elastica part. 5 fig. 1.

5. Tirare in avanti la cinghia part. 5 fino ad inserirla nella puleggia in plastica part. 4.

6. Svitare le viti part. 6; queste viti hanno la sola funzione di tenere tirata la cinghia per montare la spazzo-

la. Una volta montata la spazzola non servono più.

7. Fissare il coperchio part. 1 fig. 3 avvitando le tre viti part. 2 fig. 3.