Intended Use - Konig & Meyer 28070 Bedienungsanleitung

28070 Dulcimer stand

INTENDED USE

Durable, highly adjustable stand for dulcimers of various sizes
(depth: 453 mm-658 mm)
FEATURES & CAPABILITIES
- Stand and support are based on a solid steel construction.
- Wobble-free stand thanks to rigid four-legged construction incl.
- continuously adjustable floor leveling screw
- Individual adjustment of the playing position:
- The dulcimer support can be flexibly adjusted in height, depth
- and inclination according to personal needs
- Wide felt strips protect the instrument
- The stand folds quickly and compactly for transport and storage
- The 11515 sheet music holder is available as an option
- TECHN. DATA: Stand surface: ø 650 mm (■ 475 mm), weight: 7,2 kg
- Instrument support: Height: 700-1050 mm, depth: 453-658 mm,
- Instrument support: Width: 500/310 mm, incline: 0-45°
Thank you for choosing this product. Please read and follow these instructions
carefully before setting up and operating this product. They inform you about all
the important steps to ensure safe handling. We recommend that you keep them
for future use.
SAFETY INSTRUCTIONS
GENERAL INFORMATION
- The possibility of adjusting the product inherently involves pinching hazards.
- Careful and attentive handling during set-up, operation, dismantling and
- maintenance are therefore indispensable.
- The stand must be protected from adverse external influences such as:
- - moisture, - wind, - impacts (e.g., by the audience)
- Careful handling maintains the functionality and longevity of the product and,
- last but not least, ensures safety
- A damaged product must not be used for the time being;
- defective parts must be replaced or repaired before use
OPERATION
-Load-bearing capacity: only dulcimers that are suitable in terms of their
- design and size.
- Ensure that the surface is stable and level; use floor leveling if necessary
- Under load, the clamp and screw fittings must always be firmly tightened
- Load the support as centrally as possible, i.e. in the middle
- The instrument must be clamped between the retaining brackets:
- a dulcimer that sits too loosely represents a hazard.
- If the position of the stand or one of the settings (height, inclination, depth) is
- changed, the instrument must first be removed or secured by a second person.
SET-UP INSTRUCTIONS
1. COMPONENTS
a Base, cpl., consisting of:
a a.1 floor leveling screw, a.2 foot tubes (4x), a.3 base tube,
a a.4 snap-in clamp
b Extension tube
c Cross support
d Adjustment bracket, consisting of:
d d.1 wide AB (500 mm), d.2 narrow AB (310 mm) - each with:
d d.3 wing screw
e Accessory bag 6-28070-4-55, contents:
e e.1 felt strips, thin (2 mm), e.2 felt strips, thick (4 mm),
e e.3 caps 35 x 15 mm (2x)
f Accessories bag, upper clamp 6-28070-7-55, contents:
f f.1 carriage bolt M8 x 45 mm, f.2 washer with square hole,
f f.3 bushing ø 8,2 mm (2x), f.4 washer ø 8,4 mm, f.5 locking nut M8,
f f.6 protective cap M8, f.7 wrench SW8/SW13
g Accessory bag, clamp 6-28070-6-55, contents:
g g.1 clamp lever M8, g.2 washer ø 8,4 mm, g.3 bushing ø 8,2 mm (2x),
g g.4 washer with square hole, g.5 carriage bolt M8 x 50 mm
2. ASSEMBLY & HANDLING
BASE a
2.1 Open all four foot tubes a.2 as far as they will go and place
2.1 them on the floor
2.2 WARNING! This procedure creates a crushing hazard
2.2 WARNING! in area Q. It is therefore essential that you
2.2 WARNING! keep your limbs, clothing and other objects
2.2 WARNING! away from this area. This also applies to third parties.
2.3 Ensure that the base stands firmly and without wobbling.
2.3 Any unevenness of the floor can be compensated by turning
2.3 the knurled screw a.1.
EXTENSION TUBE b
2.4 Slightly loosen snap-in clamp a.4, pull it back and hold it like this.
2.5 Push the extension tube (open at the bottom, row of holes pointing
2.5 to the snap-in clamp) into the base tube.
2.6 Slowly release the snap-in clamp and allow it to engage - to do this,
2.6 move the extension tube slightly if necessary; then tighten the snap-in
2.6 clamp again
1. COMPONENTS
2. ASSEMBLY & HANDLING
BASE a
EXTENSION TUBE b